Drilling Intersects Multiple Epithermal Veins at Bauloora
Released
Released
Announcement PDF
ASX ANNOUNCEMENT
21 November 2023
Drilling Intersects Multiple Epithermal Veins at Bauloora
Boiling zone textures observed in diamond core at Breccia Sinter
Low-sulphidation epithermal veins
•
Multiple epithermal style veins intersected in drill holes BX001 and BX002 which are open from
surface, down dip and along strike at the Breccia Sinter Prospect.
•
Drill hole BX002 intersected two broad vein intervals of low sulphidation epithermal style veins.
•
The gold bearing potential of the Prospect area is supported by surface rock chips up to 32g/t Au,
196g/t Ag1,i and greater than 20ppb gold ii in soil anomaly 500m long and 250m wide.
Interpreted “boiling zone” intersected
•
Visual observations of fine sulphide-rich quartz bands in fibrous and moss textured chalcedonyadularia crustiform-colloform banded quartz veins, with lattice bladed quartz after carbonate, and
cockade breccia.
•
The mineralogy and textures are consistent with the top of the “boiling zone” which is commonly
well mineralised in these types of systems and gives confidence to the prospectivity at depth.
Implications of boiling zone textures
•
•
Boiling zones can have significant vertical extents with potential for bonanza gold bearing veins iii.
Multiple epithermal events support the interpretation that the Bauloora Project may host a large
and long-lived epithermal system.
Drilling Campaign Extended
•
A third hole will commence immediately to further test the newly intersected veins.
Figure 1: BX002 diamond drill core showing colloform-crustiform and cockade textures in banded chalcedony
(white-grey)-quartz (white)-adularia (cream-orange)+/- hematite (brown-red) veins and localised breccia with
rare fine pyrite-marcasite bands (dark-very dark grey-black). See Page 12 for further logging details.
Cautionary Note – Visual Estimates of Mineralisation: ‘Visual estimates of mineral abundance should never be
considered a proxy or substitute for laboratory analyses where concentrations or grades are the factor of
principal economic interest. Visual estimates also potentially provide no information regarding impurities or
deleterious physical properties relevant to valuations.’
__________________________________________
1.
See ‘Endnotes’ on Page 19 for references.
Page 1 of 19 | ABN 43 650 398 897
3/202 Russel Street Bathurst, 2795
www.legacyminerals.com.au
ASX: LGM
Page 2 of 19
Legacy Minerals Holdings Limited (ASX: LGM, “Legacy Minerals” or “the Company”) is pleased to
announce the intersection of epithermal veining at the Bauloora Project (EL8995 and EL9464) in the
Lachlan Fold Belt, NSW.
Management comment - Legacy Minerals CEO & Managing Director, Christopher Byrne said:
“The current diamond drilling program at the Breccia Sinter Prospect has delivered some spectacular
drill core and our initial interpretation is that we have intersected the upper levels of the boiling zone.
This confirms our interpretation of a preserved epithermal system at the Breccia Sinter Prospect.
The recognition of textures indicative of a boiling zone is extremely encouraging as this is the zone that
can potentially host very-high grades of gold and silver in a low sulphidation system. The presence of
boiling textures at the Breccia Sinter is evidenced by intervals of lattice bladed textures within banded
chalcedony-quartz-adularia veins and cockade breccia downhole.
Importantly, the coincidence of this interpreted boiling zone is below an area which reported significant
gold anomalism at surface in rock chip samples up to 32.2g/t Au, providing encouragement that the
veins nearby these rock chips may be gold-bearing.
With this positive outcome the drilling campaign will be expanded, and a third drill hole has now
commenced to further test these veins.”
Figure 2: Sinter outcrop above current drill holes with nearby high-grade rock chip samplesi.
SIGN UP TO LEGACY MINERALS’
INTERACTIVE INVESTOR HUB
ASX: LGM
Page 3 of 19
Figure 3. Diamond drill core photos of quartz vein textures in BX002.
SIGN UP TO LEGACY MINERALS’
INTERACTIVE INVESTOR HUB
ASX: LGM
Page 4 of 19
Figure 4. Diamond drill core photos of quartz vein textures in BX002.
SIGN UP TO LEGACY MINERALS’
INTERACTIVE INVESTOR HUB
ASX: LGM
Page 5 of 19
Figure 5. Diamond drill core photos of quartz vein textures in BX001.
SIGN UP TO LEGACY MINERALS’
INTERACTIVE INVESTOR HUB
ASX: LGM
Page 6 of 19
Figure 6: Breccia Sinter Prospect conceptual low-sulphidation epithermal schematic model showing depth
from paleo-surface, temperature, element distribution, vein textures, and alteration zones (modified from
Buchanan 1981, Morrison et. al 1995)iii.
Diamond Drilling Progress Update
At the Breccia Sinter Prospect, two diamond drill holes have been completed which tested the 500m
by 250m long gold-silver (Au-Ag) bearing low sulphidation epithermal vein zone. A large zone of
elevated gold, silver and pathfinder elements was defined in last year’s soil and extensive rock chip
sample collection program, which returned gold and silver grades up to 32.2g/t Au and 196/t Ag. In
addition, a strong audio-frequency magnetotelluric (AMT) resistivity anomaly underlies the mapped
surface sinter adding further encouragement to the geochemical signatures and result in compelling
drill targets.
Low sulphidation epithermal-style veins have been intersected in all drill holes to date. Preliminary
geological observations indicate these holes intersected host rocks that are variably altered rhyolites,
conglomerate, volcaniclastic and tuffs. Broad zones of chlorite-sericite hydrothermal alteration are
observed distal to structures and moderate to intense sericite-hematite or silica-sericite alteration
proximal to epithermal-style veins.
Drillhole BX001 intercepted a 66m thick conglomerate package before intersecting a healed fault zone
characterised by strong-intense sericite-pyrite altered porphyritic rhyolite from 126.3m to 182m with
common chalcedony (+/-pyrite-adularia) veins and silicified tectonic breccia with lesser veins of
crustiform-colloform chalcedony-quartz (+/- pyrite, hematite, galena and low-Fe sphalerite) veins.
Minor quartz-carbonate +/- chalcopyrite, galena, low-Fe sphalerite veins are also observed throughout
the drill hole.
Drill hole BX002 intercepted two zones of frequent low sulphidation epithermal-style veins
interpreted to represent the top of the targeted boiling zone between 325m to 342m and 347m and
361m. Veins are crustiform-colloform banded chalcedony-adularia veins with common moss and
fibrous quartz-adularia textures. Lattice bladed adularia and quartz after platy calcite is observed in
some bands and occasional dark grey to black bands, of fine sulphide-rich bands dominated by
marcasite and pyrite. Brecciated veins are common and are generally associated with further
chalcedony (+/- hematite) infill and cockade textures. There is occasional overprinting by chalcedonybase metal (sphalerite-galena) veins.
SIGN UP TO LEGACY MINERALS’
INTERACTIVE INVESTOR HUB
ASX: LGM
Page 7 of 19
Observations in the BX002 core samples are consistent with the hot spring depositional model used
as a basis for exploration on the project. The mineralogy and textures are consistent with the upper
part of the boiling zone which is commonly well mineralised especially near and in hydrothermal
breccias. These observations give encouragement to test further along strike and at depth. The narrow
zones of multiphase hydrothermal breccias and veins may represent the periphery or top of the
breccia body and therefore the start of the transition to a vein (over breccia) dominant character.
The diamond drill holes have confirmed low-sulphidation epithermal-style veins down dip from
elevated gold, silver and pathfinder rock chip and soil geochemical results, and mapped veins.
Preliminary down hole structural observations from these holes show veins strike north to northnorth-east and steeply west dipping (80o-85o) veins and breccias and though true widths are not yet
known, they are estimated to be 70% of the rock down hole. The vein trend remains open along strike
and down dip.
A third drill hole of 500m has been approved for the program and is expected to be completed within
the next four weeks. To date, two holes have been completed for 1,316.4m, with the last hole
expected to be completed by the beginning of December 2023.
Core processing and logging is in progress and samples will be submitted for laboratory assay analysis
upon completion of the drill campaign with results expected in February 2024. Drill hole details
provided in Table 1.
Table 1 Drill hole collar details for LGM diamond holes.
Hole ID
Easting
(MGA94/55)
Northing
(MGA94/55)
Dip
Azimuth (True
North)
Depth
(m)
Drill hole
status
BX001
589860.1
6174615
449
-60
87
795.1
Completed
BX002
590517.6
6174342
438
-60
277
521.3
Completed
BX003
590573.0
6174543
418
-65
275
500
Underway
RL (m)
Figure 7: Cross section (617450mN - 200m width) of AMT response looking north showing the location of the
Breccia Sinter historical drilling iv, and completed drill holes BX001 and BX002 over interpreted geology. See
Page 12 for further logging details.
SIGN UP TO LEGACY MINERALS’
INTERACTIVE INVESTOR HUB
ASX: LGM
Page 8 of 19
Figure 8: Location of completed and proposed drilling at the Breccia Sinter Prospect showing Sb soil results
over mapped sinter related geology v
SIGN UP TO LEGACY MINERALS’
INTERACTIVE INVESTOR HUB
ASX: LGM
Page 9 of 19
About the Bauloora Project
Legacy Minerals’ Bauloora Project is located in the Lachlan Fold Belt of New South Wales which is host
to world-class copper-gold orebodies including the Cadia-Ridgeway, Northparkes, and Cowal Mines.
In 2023, Newmont Exploration Pty Ltd entered into a Farm-In and Joint Venture on the Project vi. It
covers a large hydrothermal alteration zone 27km2 in size, within which is an anomalous gold zone
currently mapped to 15km2. Rock chip and soil samples collected by the Company from the project
area have highlighted several priority areas of anomalous precious metal values with highly
anomalous values of epithermal pathfinders vii. The drilling of the first of these targets resulted in the
discovery of the Bluecap Prospect returning 13m at 1.66g/t Au, 6.68g/t Ag, 0.14% Cu and 4.23% Pb+Zn
from 57mvii.
Extensive epithermal alteration exists on the Project, including widespread zones of high-level
chalcedonic veins, clay alteration and local sinter formations. The Project has seen very limited
exploration drilling and the Company believes the results from work to date strongly support the
assessment that there is significant potential for the discovery of a major low-sulphidation epithermalstyle gold-silver deposit at the Bauloora Project.
Figure 9: Regional setting of the Bauloora Project viii,ix,x,xi,xii
SIGN UP TO LEGACY MINERALS’
INTERACTIVE INVESTOR HUB
ASX: LGM
Page 10 of 19
Approved by the Board of Legacy Minerals Holdings Limited.
For more information:
Chris Byrne
CEO & Managing Director
chris.byrne@legacyminerals.com.au
+61 (0) 499 527 547
DISCLAIMER AND PREVIOUSLY REPORTED INFORMATION
Information in this announcement is extracted from reports lodged as market announcements referred to above
and available on the Company’s website https://legacyminerals.com.au/. The Company confirms that it is not
aware of any new information that materially affects the information included in the original market
announcement and that all material assumptions and technical parameters underpinning the estimates in the
relevant market announcement continue to apply and have not materially changed.
This announcement contains certain forward-looking statements. Forward looking statements are only
predictions and are subject to risks, uncertainties and assumptions which are outside of the control of Legacy
Minerals Holdings Limited (LGM). These risks, uncertainties and assumptions include commodity prices,
currency fluctuations, economic and financial market conditions, environmental risks and legislative, fiscal or
regulatory developments, political risks, project delay, approvals and cost estimates. Actual values, results or
events may be materially different to those contained in this announcement. Given these uncertainties, readers
are cautioned not to place reliance on forward-looking statements. Any forward-looking statements in this
announcement reflect the views of LGM only at the date of this announcement. Subject to any continuing
obligations under applicable laws and ASX Listing Rules, LGM does not undertake any obligation to update or
revise any information or any of the forward-looking statements in this announcement to reflect changes in
events, conditions or circumstances on which any forward-looking statements is based.
COMPETENT PERSON’S STATEMENT
The information in this Report that relates to Exploration Targets, Exploration Results, Mineral Resources or Ore
Reserves is based on information compiled by Thomas Wall, a Competent Person who is a Member of the
Australian Institute of Geoscientists. Mr Wall is the Technical Director and a full-time employee of Legacy
Minerals Pty Limited, the Company’s wholly-owned subsidiary, and a shareholder of the Company. Mr Wall has
sufficient experience that is relevant to the style of mineralisation and type of deposit under consideration and
to the activity being undertaken to qualify as a Competent Person as defined in the 2012 edition of the
Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves. Mr Wall consents
to the inclusion of the matters based on this information in the form and context in which it appears in this
announcement.
SIGN UP TO LEGACY MINERALS’
INTERACTIVE INVESTOR HUB
ASX: LGM
Page 11 of 19
About Legacy Minerals
Legacy Minerals is an ASX listed public company that has been involved in the acquisition and
exploration of gold, copper, and base-metal projects in the Lachlan Fold Belt since 2017. The Company
has eight projects that present significant discovery opportunities for shareholders.
Au-Cu (Pb-Zn) Cobar (EL9511)
Au Harden (EL8809, EL9257)
Undrilled targets next door to the Peak Gold Mines.
Several priority geophysical anomalies and gold in
lag up to 1.55g/t Au.
Large historical high-grade quartz-vein gold
mineralisation. Drilling includes 3.6m at 21.7g/t Au
116m and 2m at 17.17g/t Au from 111m.
Au-Ag Bauloora (EL8994, EL9464) Newmont JV
Au-Cu Fontenoy (EL8995) Earth AI-Alliance
One of NSW’s largest low-sulphidation, epithermal
systems with a 27km2 epithermal vein field and
15km2 gold zone.
An 8km long zone of Au and Cu anomalism defined
in soil sampling and drilling. Significant drill
intercepts include 79m at 0.27% Cu from 1.5m.
Cu-Au Rockley (EL8296)
Au-Ag Black Range (EL9466, EL9589)
Prospective for porphyry Cu-Au and situated in the
Macquarie Arc Ordovician host rocks with historic
high-grade copper mines that graded up to 23% Cu.
Extensive low-sulphidation, epithermal system with
limited historical exploration. Epithermal
occurrences across 30km of strike
Cu-Au Cowra (EL9614)
Cu-Au Drake (EL6273, ELA6640)
Large, drilled magnetic anomaly underneath Silurian
cover located 55kms from Cadia Valley
Large caldera (~150km2) with similar geological
characteristics to other major pacific rim.
Figure 10: Regional setting of Legacy Minerals Projects ix,x,xi,xii,xiii
SIGN UP TO LEGACY MINERALS’
INTERACTIVE INVESTOR HUB
ASX: LGM
Page 12 of 19
Appendix 1 – Drill log vein summaries
Hole ID
BX001
BX002
From
To
Downhole
width
Estimated
Vein %
Estimated
Sulphide %
Preliminary Observations - nature of mineral
occurrence, mineral identification and
estimated sulphide proportion
9
14
5
1
0.25
CC qtz-chc and chc-adu-gal (30)-sph (70)+/-hem
veins and veinlets
44
48
4
2
1
CC qtz-chc and chc-adu-gal (30)-sph (70)+/-hem
veins and veinlets
60
123.7
64
2
0.25
Qtz-crb+/-gal (30)-sph (55)-cpy (10)-py (5) veins
and veinlets
126.3
150.5
24.2
2
0.1
Healed fault zone - Chc-py (80) and chc-crb+/gal(8)-sph (10)-cpy(2) veins and veinlets
150.5
163.5
13
4
0.2
Healed fault zone - Chc-py (80)and chc-crb+/gal(8)-sph(10)-cpy(2) veins and veinlets
163.5
181
13
1
0.1
Healed fault zone - Chc-py (80)and chc-crb+/-gal
(8)-sph(10)-cpy(2) veins and veinlets
181
621
440
1
Tr
Qtz-crb veinlets
621
709
88
2
Tr
Qtz-crb+/-gal(10)-sph(90) veinlets and CC qtzchc-adl veinlets
709
795
86
1
Tr
Qtz-crb veinlets
12
12.6
0.6
60
Tr
Chc breccia
89
118
29
1
Tr
Qtz-crb veinlets
135
137
2
10
0.5
Chc-hem+/-sph(80)-gal(20)
145
168
23
1
0.1
Chc-adl-hem+/-sph(80)-gal(20)
176
177
1
20
1
Chc-adl-hem-sph(80)-gal(20) breccia
264
267
3
3
Tr
Qtz-crb veins
325
332
7
5
Tr
Chc-adl veins and veinlets
332
333
1
80
1
CC chc-adl-hem with moss and fibre
recrystallisation textures, needle adl, lattice
bladed adl after carbonate and fine mrc (80)
sulphide bands. Overprint by hydrothermal chchem breccia and later chc-sph(18)-gal(2).
333
353.5
20.5
3
0.1
CC chc-adl-py (100) with fibrous and moss
textures. Local internal hydrothermal breccia
353.5
356
2.5
80
0.1
CC chc-adl with fibrous and moss textures and
occasional fine py (100) sulphide bands.
Localised internal cockade breccia.
356
361
5
4
tr
CC chc-adl with fibrous and moss textures.
361
387
26
1
Tr
Chc-adl and qtz-crb veins and veinlets
387
443
56
0.5
Tr
Chc-adl and qtz-crb veins and veinlets
Observation codes: qtz – quartz, crb – carbonate, chc – chalcedony, adu – adularia, fl – fluorite, sph – sphalerite,
gal – galena, cpy – chalcopyrite, hem – hematite, py – pyrite, CC – crustiform-colloform, Tr – trace.
SIGN UP TO LEGACY MINERALS’
INTERACTIVE INVESTOR HUB
ASX: LGM
Page 13 of 19
Appendix 2 – JORC Code, 2021 Edition Table 1
Section 1 Sampling Techniques and Data
Criteria
JORC Code Explanation
Nature and quality of sampling (e.g., cut channels,
random chips, or specific specialised industry
standard measurement tools appropriate to the
minerals under investigation, such as down hole
gamma sondes, or handheld XRF instruments, etc).
These examples should not be taken as limiting the
broad meaning of sampling.
Sampling
Techniques
Drilling
techniques
Drill sample
recovery
Commentary
No assays are being reported in this release.
References in this announcement to visual
results are from HQ3/NQ diamond drill core.
Mineralised sections in drill core will be cut,
and half-core sampled for assaying. Assay
results are expected in February 2024.
Include reference to measures taken to ensure
sample representivity and the appropriate
calibration of any measurement tools or systems
used.
No sampling completed.
Aspects of the determination of mineralisation that
are Material to the Public Report. In cases where
‘industry standard’ work has been done this would
be relatively simple (e.g. ‘reverse circulation drilling
was used to obtain 1m samples from which 3 kg
was pulverised to produce a 30 g charge for fire
assay’). In other cases more explanation may be
required, such as where there is coarse gold that
has inherent sampling problems. Unusual
commodities or mineralisation types (e.g.,
submarine nodules) may warrant disclosure of
detailed information.
No assays are being reported in this release.
Drill type (e.g., core, reverse circulation, open‐hole
hammer, rotary air blast, auger, Bangka, sonic, etc)
and details (e.g. core diametre, triple or standard
tube, depth of diamond tails, face sampling bit or
other type, whether core is oriented and if so, by
what method, etc).
Diamond drilling is completed using HQ3 drill
core. Core orientation completed using a
REFLEX tool.
Method of recording and assessing core and chip
sample recoveries and results assessed.
Core recovery is captured in the core logging.
No assays are being reported in this release.
Measures taken to maximise sample recovery and
ensure representative nature of the samples.
No assays are being reported in this release.
Whether a relationship exists between sample
recovery and grade and whether sample bias may
have occurred due to preferential loss/gain of
fine/coarse material.
To date, minimal sample recovery issues have
been identified that would impact on
potential sample bias in the competent fresh
rocks that host the mineralised sulphide
intervals.
Systematic geological and geotechnical
logging was undertaken. Data collection
where appropriate includes:
• Nature and extent of lithologies.
• Relationship between lithologies.
• Amount and mode of occurrence of ore
minerals.
• Location, extent and nature of structures
such as bedding, cleavage, veins, faults etc.
Structural data (alpha & beta) are recorded
for orientated core.
• Geotechnical data is collected as required
such as recovery, RQD, fracture frequency,
SIGN UP TO LEGACY MINERALS’
INTERACTIVE INVESTOR HUB
ASX: LGM
Page 14 of 19
qualitative IRS, microfractures, veinlets and
number of defect sets. For some geotechnical
holes the orientation, nature of defects and
defect fill may be recorded.
• Bulk density by Archimedes principle at
regular intervals may be taken.
• Magnetic susceptibility recorded at 1m
intervals for some holes as an orientation and
alteration characterisation tool.
Whether core and chip samples have been
geologically and geotechnically logged to a level of
detail to support appropriate Mineral Resource
estimation, mining studies and metallurgical
studies.
Logging
Sub‐sampling
techniques and
sample
preparation
Whether logging is qualitative or quantitative in
nature. Core (or costean, channel, etc)
photography.
Logging of records lithology, mineralogy,
mineralisation, structures, weathering, colour
and other noticeable features. This is
generally qualitative except for % of sulphides
and vein mineral content. Core trays are
photographed in wet form.
The total length and percentage of the relevant
intersections logged.
All drill holes are geologically logged in full.
If core, whether cut or sawn and whether quarter,
half or all core taken.
If non‐core, whether riffled, tube sampled, rotary
split, etc and whether sampled wet or dry.
No assays are being reported in this release.
For all sample types, the nature, quality and
appropriateness of the sample preparation
technique.
No sampling completed.
Quality control procedures adopted for all
subsampling stages to maximise representivity of
samples.
Measures taken to ensure that the sampling is
representative of the in situ material collected,
including for instance results for field
duplicate/second‐half sampling.
Quality of
assay data and
laboratory
tests
Geological logging is carried out on all drill
hole chips with lithology, alteration,
mineralisation, structure and veining recorded
where possible.
No assays are being reported in this release.
No sampling completed.
No sampling completed.
Whether sample sizes are appropriate to the grain
size of the material being sampled.
No sampling completed.
The nature, quality and appropriateness of the
assaying and laboratory procedures used and
whether the technique is considered partial or total.
No assays are being reported in this release.
For geophysical tools, spectrometres, handheld XRF
instruments, etc, the parametres used in
determining the analysis including instrument make
and model, reading times, calibrations factors
applied and their derivation, etc.
No assays are being reported in this release.
Nature of quality control procedures adopted (e.g.
standards, blanks, duplicates, external laboratory
checks) and whether acceptable levels of accuracy
(i.e. lack of bias) and precision have been
established.
No assays are being reported in this release.
The verification of significant intersections by either
independent or alternative company personnel.
No assays are being reported in this release.
SIGN UP TO LEGACY MINERALS’
INTERACTIVE INVESTOR HUB
ASX: LGM
Page 15 of 19
Verification of
sampling and
assaying
The use of twinned holes.
Documentation of primary data, data entry
procedures, data verification, data storage (physical
and electronic) protocols.
Discuss any adjustment to assay data.
Location of
data points
Accuracy and quality of surveys used to locate drill
holes (collar and down‐hole surveys), trenches, mine
workings and other locations used in Mineral
Resource estimation.
Specification of the grid system used.
Quality and adequacy of topographic control.
Data spacing for reporting of Exploration Results.
Data spacing
and
distribution
Whether the data spacing and distribution is
sufficient to establish the degree of geological and
grade continuity appropriate for the Mineral
Resource and Ore Reserve estimation procedure(s)
and classifications applied. Whether sample
compositing has been applied.
Whether sample compositing has been applied.
Orientation of
data in
relation to
geological
structure
Whether the orientation of sampling achieves
unbiased sampling of possible structures and the
extent to which this is known, considering the
deposit type.
No twinned holes have been planned for the
current drill programme.
Primary data is captured onto a laptop
through excel and using Datashed software
and includes geological logging, sample data
and QA/QC information. This data, together
with the assay data, is stored both locally and
entered into the LGM central online database.
No adjustments or calibrations will be made
to any primary assay data collected for the
purpose of reporting assay grades and
mineralised intervals. For the geological
analysis, standards and recognised factors
may be used to calculate the oxide form
assayed elements, or to calculate volatile free
mineral levels in rocks.
A handheld Garmin GPSmap 65 was used to
pick up collars with an averaged accuracy of
1m.
Downhole surveys are conducted using a
downhole Gyro during drilling to record and
monitor deviations of the hole from the
planned dip and azimuth.
The grid system used is GDA94, MGA Zone 55.
Using government data topography and 2017
DTM data. A topographic surface has been
created using this elevation data.
The spacing and distribution of holes is not
relevant to the drilling programs which are at
the exploration stage rather than definition
drilling. Drill holes were preferentially located
at those areas considered most prospective.
No sampling completed.
No compositing has been applied to the
exploration results.
The drill holes are orientated to intersect the
dipping mineralised trends at as near
perpendicular orientation possible (unless
otherwise stated).
The orientation of key structures may be
locally variable and any relationship to
mineralisation has yet to be identified.
The orientation of drilling relative to key
mineralised structures is not considered likely
to introduce sampling bias.
If the relationship between the drilling orientation
and the orientation of key mineralised structures is
considered to have introduced a sampling bias, this
should be assessed and reported if material.
Orientation of the mineralisation and
structural trends is constrained by previous
drilling and outcrop.
SIGN UP TO LEGACY MINERALS’
INTERACTIVE INVESTOR HUB
ASX: LGM
Page 16 of 19
The orientation of sampling is considered
appropriate for the current geological
interpretation of the mineral style.
No sample bias due to drilling orientation is
known.
Sample
security
The measures taken to ensure sample security.
Audits or
reviews
The results of any audits or reviews of sampling
techniques and data.
Chain of Custody is managed by the Company
until samples pass to a certified assay
laboratory for subsampling and assaying. The
core trays are stored on secure sites and
delivered to the assay laboratory by the
Company or a competent agent. When not in
transit, they are kept in locked premises.
Where appropriate transport logs have been
set up to track the progress of samples.
Sampling techniques and procedures are
regularly reviewed internally, as is data. To
date, no audits of sampling techniques and
data have been completed on the drilling
programme.
Section 2 Reporting of Exploration Results
(Criteria in this section apply to all succeeding section)
Criteria
JORC Code Explanation
Commentary
Mineral
Tenement and
Land Status
Type, name/reference number, location and
ownership including agreements or
material issues with third parties including
joint ventures, partnerships, overriding
royalties, native title interests, historical
sites, wilderness or national park and
environmental settings.
The Bauloora Project is comprised of EL8994 and
EL9464. The license is owned 100% by Legacy
Minerals Pty Ltd (a fully owned subsidiary of Legacy
Minerals Holdings Limited). There are no royalties or
encumbrances over the tenement areas.
The security of the tenure held at the time
of reporting along with any known
impediments to obtaining a licence to
operate in the area.
The land is primarily freehold land. There are no
native title interests in the license area.
Exploration
Done by Other
Parties
Acknowledgment and appraisal of
exploration by other parties.
Geology
Deposit type, geological setting and style of
mineralisation
Drill hole
Information
A summary of all information material to
the understanding of the exploration results
including tabulation of the following
information for all Material drill holes:
Teck Exploration - conducted mapping, IP geophysics,
rock chip sampling, diamond and RC drilling. BP
Minerals/MM&S - conducted detailed mapping,
geochemical sampling and AC drilling. Billiton
Australia - conducted mapping, IP geophysics, rock
chip sampling. North Limited – rock chip sampling,
soil sampling, drilled AC and RC holes. Robust
Resources – soil sampling diamond and RC drilling.
Bushman Resources – Rock chip sampling.
Known mineralisation at the Bauloora Project sits
within the Silurian Frampton Volcanics, and
Devonian Bethungra Formation, Cowcumba
Share your feedback
Discover