Maiden Drilling Intersects Semi-Massive Sulphides
Released
Released
Announcement PDF
ASX ANNOUNCEMENT
24 FEB 2022
Maiden Drilling Intersects Semi-Massive Sulphides
Base-metal sulphide mineralisation has been logged in all three completed drill holes
Highlights
•
•
•
•
•
•
Vein-hosted base-metal mineralised zones up to 10m width 1 have been intercepted in the
first 3 reverse circulation (RC) drill holes at the Mt Felstead Prospect
Assays of these sulphide zones have the potential to return high zinc and lead values plus
copper, silver, and gold1
Drilling is ongoing as parts of a 9-hole campaign totalling approximately 1,500m
The drilling is testing down dip of known mineralisation and along a 650m strike of
historically mined mineralisation and anomalous soil geochemistry
The Mt Felstead Prospect exhibits carbonate base metal epithermal-style gold-silver
mineralisation which historically reported bonanza Ag and high-grade Au that included:
o 3,701g/t Ag, 6.9g/t Au, 55% Pb+Zn, and 6.4% Cu (20cm face grab sample)
The Mt Felstead Prospect is the first of several high priority target to be drill tested in the
Bauloora Project which covers a 27km2 area zone of hydrothermal alteration
Figure 1: Sulphide mineralisation; sphalerite (brown-purple) and galena (silver) in RC hole BM002 at 99m
1
In relation to the disclosure of visual mineralisation, the Company cautions that visual estimates of sulphide and oxide material abundance should
never be considered a proxy or substitute for laboratory analysis. Laboratory assays results are required to determine the widths and grade of the
visible mineralisation reported in preliminary geological logging.
ABN 43 650 398 897
Level 7, 1 Margaret Street Sydney
ASX: LGM
Page 1 of 13
www.legacyminerals.com.au
Management Comment
Legacy Minerals Managing Director, Christopher Byrne said:
“We are excited to start drilling the large low-sulphidation epithermal-style gold silver mineralisation
at Bauloora with the maiden campaign into the historic high-grade gold-silver Mt Felstead Mine
Prospect.
The observation of base-metal sulphides intercepted in all three holes to date are very encouraging
particularly with the historical association between silver -gold with sphalerite and galena
mineralisation in drill and mine assay data.
An additional 5 reverse circulation percussion (RC) drill holes will be completed that could
significantly extend the known mineralised along strike and down-dip. Assays are expected within 48 weeks of the completion of the campaign, and I look forward to keeping the investors up to date
on the progress.”
Figure 2: Veined-hosted sulphide mineralisation; sphalerite (brown-purple), galena (silver grey) and
chalcopyrite (golden yellow) in RC hole BM001 from 111-117m
Summary of Mt Felstead Prospect
The Mt Felstead prospect, which includes historical mines such as the Bauloora Mine, is located
10km north-west of Cootamundra and was discovered in the early 1900’s with intermittent mining
up to the mid-1950’s. The Bauloora Project (EL8994) contains several known minor workings hosted
within the Silurian Frampton Volcanics and Devonian Bethungra Formation, Cowcumbala Rhyolite
and Deep Gully Creek Conglomerate. The workings of the Bauloora Project sit within a large 27km2
hydrothermal alteration and mineralisation zone identified through previous geological mapping
and geochemical sampling.
Page 2 of 13 | ABN 43 650 398 897
Level 7, 1 Margaret Street Sydney
www.legacyminerals.com.au
ASX: LGM
Mineralisation at the Mt Felstead Prospect occurs as a steeply dipping lenticular zone developed in
a fault breccia that trends 330° magnetic. This zone is over 250 m long, up to 2.5 m wide and was
worked to a depth of 60 m. Further mineralisation has been noted to occur along the strike for about
250m. Historically the ore minerals have included argentiferous galena, sphalerite, chalcopyrite,
tetrahedrite, and gold. The gangue minerals included quartz, chalcedony, calcite, chlorite, fluorite,
and lesser barite.
Historical sampling shows potential for bonanza grade silver and high grade gold mineralisation at
the Bauloora mine. It was reported that an un-mined production drive ~60m long, 0.7m wide
averaged assays of 1,021.5g/t Ag, 7.2g/t Au, 22.2% Pb+Zn and 2.5% Cu. Epithermal gold-silver-base
metal style mineralisation has been traced for approximately 400m and occurs in replacement
breccia that defines a fault zone trending north south. No leaching or secondary enrichment has
been identified. The drill campaign has been designed to test dip and strike extensions of bonanza
silver and high-grade gold associated with base metal mineralisation historically mined at the
Bauloora Mine.
Drilling Progress
The three out of a total 9 RC holes have ranged from 120 to 220 metres depth (Figure 3 and Figure
4). The interpreted position of the mineralised structure has been intercepted in all holes to date.
Host rocks were variably silicified rhyodacite tuffs, with sericite alteration noted in association with
shearing and chlorite-epidote alteration increasing in intensity adjacent to quartz-carbonate veins.
Sulphides were observed to occur with quartz-carbonate veining (Figure 1 and Figure 2). These veins
consisted primarily of fine-grained sphalerite and fine grained “sooty” galena with minor
chalcopyrite and disseminated pyrite.
Figure 3: Mt Felstead Prospect long section showing completed and planned drill holes
Page 3 of 13 | ABN 43 650 398 897
Level 7, 1 Margaret Street Sydney
www.legacyminerals.com.au
ASX: LGM
Figure 4: Plan view of Mt Felstead Prospect showing completed and planned holes
Next Steps at the Bauloora Project (EL8994)
The next steps for the Bauloora project include the completion of the remaining RC drill holes at the
Bauloora Mine prospect. Legacy Minerals has also completed the planning for testing the
applicability of down hole electromagnetic (DHEM) surveying at the prospect with three holes
prepared for the survey. The Company also expects the results of the 90 line-km gradient array
induced polarisation (GA-IP) program within the next two weeks (Figure 4). These results are highly
anticipated given the anomalous geochemistry across the larger Bauloora Project.
Page 4 of 13 | ABN 43 650 398 897
Level 7, 1 Margaret Street Sydney
www.legacyminerals.com.au
ASX: LGM
Figure 5: The Bauloora Project Area and prospects showing the anomalous gold zone and recently
completed GA-IP Survey Area
Page 5 of 13 | ABN 43 650 398 897
Level 7, 1 Margaret Street Sydney
www.legacyminerals.com.au
ASX: LGM
Table 1. Drill hole collar details for completed RC drill holes
Drillhole Name
BM001
BM002
BM003
Easting Northing Elevation
Datum
Azimuth Dip EOH
588373 6175623
460 GDA94 / MGA zone 55
90 55 144
588373 6175616
460 GDA94 / MGA zone 55
110 50 120
588336 6175681
453 GDA94 / MGA zone 55
90 60 220
Mt Felstead pXRF Soil Sampling
Soil sampling utilising pXRF can be a quick and effective method of sampling when completed using
a systematic methodology with regular QAQC and validation, refer 2015 AIG QLD pXRF symposium
in references. Soil sampling for base metals such as copper and lead and pathfinders such as arsenic
can be reliably detectable using a pXRF if systematic procedures are followed. Further details of the
survey methodology can be found in the JORC Table, attached.
Page 6 of 13 | ABN 43 650 398 897
Level 7, 1 Margaret Street Sydney
www.legacyminerals.com.au
ASX: LGM
Approved by the board of Legacy Minerals Holdings Limited.
For more information:
Chris Byrne
CEO & Managing Director
chris.byrne@legacyminerals.com.au
+61 (0) 499 527 547
Victoria Humphries
Media & Investor Relations
victoria@nwrcommunications.com.au
+61 (0) 431 151 676
DISCLAIMER & COMPETENT PERSONS STATEMENT
Information in this announcement is extracted from reports lodged as market announcements referred to above and
available on the Company’s website https://legacyminerals.com.au/. The Company confirms that it is not aware of any
new information that materially affects the information included in the original market announcement and that all
material assumptions and technical parameters underpinning the estimates in the relevant market announcement
continue to apply and have not materially changed.
This announcement contains certain forward-looking statements. Forward looking statements are only predictions and
are subject to risks, uncertainties and assumptions which are outside of the control of Legacy Minerals Holdings Limited
(LGM). These risks, uncertainties and assumptions include commodity prices, currency fluctuations, economic and
financial market conditions, environmental risks and legislative, fiscal or regulatory developments, political risks, project
delay, approvals and cost estimates. Actual values, results or events may be materially different to those contained in
this announcement. Given these uncertainties, readers are cautioned not to place reliance on forward-looking
statements. Any forward-looking statements in this announcement reflect the views of LGM only at the date of this
announcement. Subject to any continuing obligations under applicable laws and ASX Listing Rules, LGM does not
undertake any obligation to update or revise any information or any of the forward-looking statements in this
announcement to reflect changes in events, conditions or circumstances on which any forward-looking statements is
based.
The information in this report that relates to Exploration Targets, Exploration Results, Mineral Resources or Ore
Reserves is based on information compiled by Thomas Wall, a Competent Person who is a Member of the Australian
Institute of Geoscientists. Mr Wall is the Technical Director is a full-time employee of Legacy Minerals Limited and a
shareholder, who has sufficient experience that is relevant to the style of mineralisation and type of deposit under
consideration and to the activity being undertaken to qualify as a Competent Person as defined in the 2012 edition of
the Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves. Mr Wall consents to
the inclusion in the report of the matters based on his information in the form and context in which it appears in this
announcement.
REFERENCED DOCUMENTS
Company’s Prospectus dated 28 July 2021;
Australian Institute of Geoscientists; pXRF Geochemistry: use and abuse in exploration and mining – Friday Seminar
Series 13th November 2015 https://www.aig.org.au/librar/seminar-presentations/qld-branch-presentationsevents/aig-qldpresentations-pxrf-geochemistry/
Page 7 of 13 | ABN 43 650 398 897
Level 7, 1 Margaret Street Sydney
www.legacyminerals.com.au
ASX: LGM
About Legacy Minerals
Legacy Minerals is an ASX listed public Company that has been involved in the acquisition and exploration of
gold, copper, and base-metal projects in the Lachlan Fold Belt since 2017. The Company has five wholly
owned and unencumbered tenements that present significant discovery opportunities.
Au-Cu (Pb-Zn) Cobar (EL8709, EL9256)
Au Harden (EL8809, EL9257)
Undrilled targets next door to the Peak Gold Mines with
several priority geophysical anomalies Late time AEM
conductors, IP anomaly, and magnetic targets
Geochemically anomalous - gold in lag up to 1.55g/t Au
Large historical high-grade quartz-vein gold
mineralisation open along strike and down plunge.
Significant drill intercepts include 3.6m at 21.7g/t Au
116m and 2m at 19.09g/t Au from 111m
Au-Ag Bauloora (EL8994)
Au-Cu Fontenoy (EL8995)
A 27km hydrothermal alteration area large containing
low-sulphidation epithermal-style gold silver targets.
Historical bonanza grades at the Mt Felstead Prospect
included 3,701g/t Ag, 6.9g/t Au, 29% Pb, 26% Zn, and
6.4% Cu (20cm grap sample)
The Project exhibits a greater than 8km long zone of Au
and Cu anomalism defined in soil sampling and drilling.
Significant drill intercepts include 79m at 0.27% Cu from
1.5m
Cu-Au Rockley (EL8296)
Sn-Ni-Cu Mulholland (EL9330)
Prospective for porphyry Cu-Au and situated in the
Macquarie Arc Ordovician host rocks the project
contains historic high-grade copper mines and rock
chips up to 4.26% Cu and 90g/t Ag.
Associated polymetallic mineralisation. There are
several tin and nickel occurrences in the project area
with trends up to 2.6km defined in drilling. Significant
drill intercepts include 44m at 0.45% Ni
2
Figure 6: Legacy Minerals’ Tenements, Lachlan Fold Belt NSW
Page 8 of 13 | ABN 43 650 398 897
Level 7, 1 Margaret Street Sydney
www.legacyminerals.com.au
ASX: LGM
Appendix 1 – JORC Code, 2021 Edition Table 1
Section 1 Sampling Techniques and Data
Criteria
JORC Code Explanation
Commentary
Nature and quality of sampling (e.g., cut channels,
random chips, or specific specialised industry
standard measurement tools appropriate to the
minerals under investigation, such as down hole
gamma sondes, or handheld XRF instruments, etc).
These examples should not be taken as limiting the
broad meaning of sampling.
RC Sampling: All samples from the RC drilling are taken as 1m
samples for laboratory assay. Samples are collected using
cone or riffle splitter. Geological logging of RC chips is
completed at site with representative chips being stored in
drill chip trays. Magnetic susceptibility was recorded from the
green bulk bag for each meter by a KT-10 mag sus meter.
Soil Sampling: A handheld XRF analyser was used to obtain
soil analyses. The unit is a 2019 Olympus Vanta pXRF.
A total of 420 samples were analysed on a systematic grid,
50m apart on 50m line spacing. Sample sites were prepared
by digging/scuffing to 5-20cm depth to remove the vegetation
and topsoil. An un-sieved soil sample was collected 0.3-0.5kg
in weight. At the field office the instrument was then used to
analyse the soil sample directly. A very thin sandwich bag was
placed over the front of the analyser to protect it from dust
and contamination.
Include reference to measures taken to ensure
sample representivity and the appropriate
calibration of any measurement tools or
systems used.
Sampling
Techniques
RC Sampling: Samples are taken on a one metre basis and
collected using uniquely numbered calico bags. The remaining
material for that metre is collected and stored in a green
plastic bag marked with that specific metre interval. The
cyclone is cleaned with compressed air after each plastic and
calico sample bag is removed. If wet sample or clays are
encountered then the cyclone is opened and cleaned
manually and with the aid of a compressed air gun. A blank
sample is inserted at the beginning of each hole, and a
duplicate sample is taken every 50th sample. A certified
sample standard is also added according to geology, but at no
more than 1:50 samples.
Geological logging of RC chips is completed at site with
representative chips being stored in drill chip trays. Downhole
surveys of dip and azimuth are conducted using a single shot
camera every 30m, and using a downhole Gyro when
required, to detect deviations of the hole from the planned
dip and azimuth. The drill‐hole collar locations are recorded
using a hand‐held GPS, which has an accuracy of +/‐ 5m. All
drill‐hole collars may be surveyed to a greater degree of
accuracy using a certified surveyor at a later date.
An Olympus Vanta pXRF is used to systematically analyse the
RC sample onsite. One reading is taken per metre with field
calibration of the pXRF instrument using standards
periodically performed (usually daily).
The handheld pXRF results are only used for preliminary
assessment of element compositions, prior to the receipt of
assay results from the certified laboratory.
Soil Sampling: Written procedures for pXRF sampling and
QAQC were developed and caried out by LGM staff using up
to date techniques. The pXRF is calibrated and blanks
analysed at the start and end of each day. Sampling technique
is considered appropriate for the geology and style of
mineralisation. See references.
A previous explorers ICPMS & ICPOE analysed soil samples
over the area were repeated using a pXRF during this survey
to ensure repeatability. These two datasets have been
compared and anomalies are considered comparable hence
the Company is confident in the pXRF soil method used for
the elements reported.
The soil was analysed only if relatively dry. Wet soil was not
analysed. Battery is changed when at 25%. The pXRF machine
is calibrated by Olympus annually. The Vanta is a three beam
analyser, each beam time was set to 20 seconds, giving total
read time as 60 seconds.
Location by hand held GPS device to 3m accuracy, GDA94
zone 55
Drilling
techniques
Drill sample
recovery
Logging
Aspects of the determination of mineralisation
that are Material to the Public Report.
In cases where ‘industry standard’ work has
been done this would be relatively simple (e.g.
‘reverse circulation drilling was used to obtain 1
m samples from which 3 kg was pulverised to
produce a 30 g charge for fire assay’). In other
cases more explanation may be required, such
as where there is coarse gold that has inherent
sampling problems. Unusual commodities or
mineralisation types (eg submarine nodules)
may warrant disclosure of detailed information.
Drill type (eg core, reverse circulation, open‐hole
hammer, rotary air blast, auger, Bangka, sonic,
etc) and details (eg core diametre, triple or
standard tube, depth of diamond tails, facesampling
bit or other type, whether core is
oriented and if so, by what method, etc).
Method of recording and assessing core and
chip sample recoveries and results assessed.
Measures taken to maximise sample recovery
and ensure representative nature of the
samples.
Whether a relationship exists between sample
recovery and grade and whether sample bias
may have occurred due to preferential loss/gain
of fine/coarse material.
Whether core and chip samples have been
geologically and geotechnically logged to a level
of detail to support appropriate Mineral
Resource estimation, mining studies and
metallurgical studies.
Whether logging is qualitative or quantitative in
nature. Core (or costean, channel, etc)
photography.
The total length and percentage of the relevant
intersections logged.
Sub‐sampling
techniques and
sample
preparation
If core, whether cut or sawn and whether quarter,
half or all core taken.
If non‐core, whether riffled, tube sampled,
rotary split, etc and whether sampled wet or
dry.
For all sample types, the nature, quality and
appropriateness of the sample preparation
technique.
Mineralisation was not yet determined. The holes were
geologically logged and the magnetic susceptibility was
recorded from the calico bag for each meter by a KT-10 mag
sus meter.
Samples have been sent to a laboratory and will be reported
upon once results are received.
RC Sampling: The RC drilling uses a 140 mm diameter face
hammer tool. High capacity air compressors on the drill rig are
used to ensure a continuously sealed and high‐pressure
system during drilling to maximise the recovery of the drill
cuttings, and to ensure chips remain dry to the maximum
extent possible.
RC Sampling: RC samples are visually checked for recovery,
moisture and contamination. Geological logging is completed
at site with representative RC chips stored in chip trays.
Sample weights were recorded on site using digital scales for
each calico sample.
RC Sampling: Samples are collected using cone or riffle
splitter.
Geological logging of RC chips is completed at site with
representative chips being stored in drill chip trays. Sample
sizes were monitored and the splitter was regularly agitated
to reduce the potential for sample contamination
To date, no sample recovery issues have yet been identified
that would impact on potential sample bias in the competent
fresh rocks that host the mineralised sulphide intervals.
Geological logging is carried out on all drill holes with
lithology, alteration, mineralisation, structure and veining
recorded.
Logging of RC samples records lithology,mineralogy,
mineralisation, structures, weathering, colour and other
noticeable features. Chip trays were photographed in wet
form.
All drill holes are geologically logged in full and
lithogeochemical information is collected by the field XRF
unit. The data relating to the elements analysed is used to
determine further information regarding the rock
composition.
NA
RC samples are collected using acone or riffle splitter when
available. Geological logging of RC chips is completed at site
with representative chips being stored in drill chip trays.
RC Sampling: Sample preparation for RC chips follows a
standard protocol. If a sample is wet or damp it is recorded.
Most samples were dry.
Sample preparation will comprise of an industry standard
of drying, jaw crushing and pulverising to -75 microns (85%
passing). Samples are dried, crushed and pulverized to
produce a homogenous representative sub‐sample for
analysis.
Soil Sampling: Samples were collected in mostly dry
conditions and placed in numbered paper soil sampling bags
and grouped in polyweave bags for later dispatch to the
laboratory.
Sample size was generally 0.3-0.5kg.
Samples are taken directly to the Legacy Minerals field offices
in Murrumburrah or Bathurst, NSW after completion of the
program.
Samples subjected to pXRF analysis did not undergo any
sample preparation procedures.
Quality control procedures adopted for all
subsampling
stages to maximise representivity of
samples.
The sample methods are considered appropriate for the fine
grain nature of the soils being analysed
Quality control procedures include submission of Certified
Reference Materials (standards) and duplicates with each
sample batch. QAQC results are routinely reviewed to identify
and resolve any issues.
RC Sampling: Field QC procedures maximise representivity of
RC samples and involve the use of certified reference material
as assay standards, along with blanks, duplicates and barren
washes.
Measures taken to ensure that the sampling is
representative of the in situ material collected,
including for instance results for field
duplicate/second‐half sampling.
Whether sample sizes are appropriate to the
grain size of the material being sampled.
The nature, quality and appropriateness of the
assaying and laboratory procedures used and
whether the technique is considered partial or
total.
For geophysical tools, spectrometres, handheld
XRF instruments, etc, the parametres used in
determining the analysis including instrument
make and model, reading times, calibrations
factors applied and their derivation, etc.
Quality of
assay data and
laboratory
tests
Soil Sampling: Any reconciliation (extra samples, insufficient
sample, missing samples) is noted upon delivery to the Field
office or during standard QA/QC audit procedures.
RC sampling: Duplicate RC samples are captured using two
separate sampling apertures on the splitter approximately
every 50m.
The sample sizes are considered to be appropriate to correctly
represent gold mineralisation and associated geology based
on: the style of mineralisation, the thickness and consistency
of the intersections and the sampling methodology.
Not applicable: Lab data not being reported
An Olympus Vanta pXRF, three beam analyser, with beam
times set to 20, 10 and 10 seconds, giving total read time as
40 seconds is used to systematically analyse the sample
onsite. One reading is taken per metre. Field
calibration of the XRF instrument using standards is
periodically performed (usually daily).
The handheld pXRF results are only used for preliminary
assessment of element compositions, prior to the receipt of
assay results from the certified laboratory.
Soil Sampling: An Olympus Vanta pXRF, three beam analyser,
with beam times set to 20, 20 and 20 seconds, giving total
read time as 60 seconds is used to systematically analyse the
samples.
Nature of quality control procedures adopted
(eg standards, blanks, duplicates, external
laboratory checks) and whether acceptable
levels of accuracy (ie lack of bias) and precision
have been established.
No calibration factors applied.
Laboratory QAQC involves the use of internal lab standards
using certified reference material (CRMs), blanks and pulp
duplicates as part of in‐house procedures. The Company also
submits a suite of CRMs, blanks where appropriate and
selects appropriate samples for duplicates.
The verification of significant intersections by
either independent or alternative company
personnel.
The use of twinned holes.
Verification of
sampling and
assaying
Documentation of primary data, data entry
procedures, data verification, data storage
(physical and electronic) protocols.
Discuss any adjustment to assay data.
Location of
data points
Accuracy and quality of surveys used to locate
drill holes (collar and down‐hole surveys),
trenches, mine workings and other locations
used in Mineral Resource estimation.
Sample preparation checks for fineness are performed by the
laboratory to ensure the grind size of 85% passing 75μm is
being attained.
Significant intersections are verified by the Company’s
technical staff.
Soil Sampling: Discussed above under ‘sampling techniques’
No twinned holes have been planned for the current drill
programme.
Primary data is captured onto a laptop through excel and
using Datashed software and includes geological logging,
sample data and QA/QC information. This data, together with
the assay data, is stored both locally and entered into the
LGM central online database which is managed by external
consultants.
No adjustments or calibrations will be made to any primary
assay data collected for the purpose of reporting assay grades
and mineralised intervals. For the geological analysis,
standards and recognised factors may be used to calculate the
oxide form assayed elements, or to calculate volatile free
mineral levels in rocks.
A handheld Garmin GPSmap 65 was used to pick up collars
with an averaged accuracy of 1m.
Downhole surveys are conducted using a single shot camera
approximately every 30m or downhole Gyro during drilling to
record and monitor deviations of the hole from the planned
dip and azimuth.
Soil Sampling: A handheld Garmin GPSmap 65 was used to
pick up sample sites with an accuracy of 3m.
Specification of the grid system used.
Quality and adequacy of topographic control.
Data spacing
and
distribution
Orientation of
data in relation
to geological
structure
Sample
security
Data spacing for reporting of Exploration
Results.
Whether the data spacing and distribution is
sufficient to establish the degree of geological
and grade continuity appropriate for the
Mineral Resource and Ore Reserve estimation
procedure(s) and classifications applied. Whether
sample compositing has been applied.
Whether sample compositing has been applied.
Whether the orientation of sampling achieves
unbiased sampling of possible structures and
the extent to which this is known, considering
the deposit type.
If the relationship between the drilling
orientation and the orientation of key
mineralised structures is considered to have
introduced a sampling bias, this should be
assessed and reported if material.
The measures taken to ensure sample security.
The grid system used is WGS84 and may be transformed into
GDA94, MGA Zone 55.
Using government data topography and 2017 DTM data. A
topographic surface has been created using this elevation
data
The spacing and distribution of holes is not relevant to the
drilling programs which are at the exploration stage rather
than definition drilling.
Soil sampling: Samples were analysed on a systematic grid,
50m apart on 50m spaced lines (50m x 50m grid)
The completed drilling at the Project is not sufficient to
establish the degree of geological and grade continuity to
support the definition of Mineral Resource and Reserves and
the classifications applied under the 2012 JORC code.
No compositing has been applied to the exploration results.
The drill holes are drilled to intersect the modelled
mineralised zones at as near perpendicular orientation
possible (unless otherwise stated). However, the orientation
of key structures may be locally variable and any relationship
to mineralisation has yet to be identified.
No orientation-based sampling bias has been identified in the
data to date.
Chain of Custody is managed by the Company until samples
pass to a certified assay laboratory for subsampling and
assaying. The RC sample bags are stored on secure sites and
delivered to the assay laboratory by the Company or a
competent agent. When in transit, they are kept in locked
premises. Transport logs have been set up to track the
progress of samples.
Audits or
reviews
The results of any audits or reviews of sampling
techniques and data.
Sampling techniques and procedures are regularly reviewed
internally, as is data. To date, no external audits have been
completed on the drilling programme.
Section 2 Reporting of Exploration Results
(Criteria in this section apply to all succeeding section)
Criteria
Mineral
Tenement and
Land Status
Exploration
Done by Other
Parties
Geology
Drill hole
Information
Data
aggregation
methods
Relationship
between
mineralisation
widths and
intercept
lengths
Diagrams
JORC Code Explanation
Commentary
Type, name/reference number, location and
ownership including agreements or material
issues with third parties including joint ventures,
partnerships, overriding royalties, native title
interests, historical sites, wilderness or national
park and environmental settings.
The Bauloora Project is comprised of EL8994. The license is
owned 100% by Legacy Minerals Pty Ltd (a fully owned
subsidiary of Legacy Minerals Holdings Limited). There are no
royalties or encumbrances over the tenement areas.
The security of the tenure held at the time of
reporting along with any known impediments to
obtaining a licence to operate in the area.
Acknowledgment and appraisal of exploration
by other parties.
Deposit type, geological setting and style of
mineralisation
A summary of all information material to the
underst
Share your feedback
Discover