Additional High-Grade Gold Assays at Harden
Released
Released
Announcement PDF
ASX ANNOUNCEMENT
5 OCT 2021
Additional High-Grade Gold Assays at Harden
Broad mineralised zones intercepted along strike
•
•
•
•
•
Assay results received from 3 additional holes at the Harden Gold Mine Prospect
Significant drilling intercepts include:
— Hole RC21HN006 3m at 4.62g/t Au from 79m
within 8m at 2.45g/t Au from 77m.
— Hole RC21HN003 9m at 0.56g/t Au from 120m;
4m at 0.51g/t Au from 133m
within 8m at 0.38g/t Au from 133m
The intersection in hole RC21HN006 occurs 50m up dip of the previously released hole RC21HN005
which recorded an intersection of 2m at 19.09g/t within 5m at 7.81g/t Au from 110m1
The broad gold zones intercepted in Hole RC21HN003 are located 175m east along strike of the highgrade intersections of Hole RC21HN006 and demonstrates the growth potential within this system
Assays are pending for the remaining 6 holes
RC21HN006 80-81m
Management Comment
Legacy Minerals Managing Director, Christopher Byrne said:
“The Harden Gold Mine prospect continues to deliver exceptional results for Legacy Minerals. The grades,
strike and widths seen in the recently completed drillholes greatly expand the knowledge of the
mineralisation. It is exciting to see the extent of the mineralisation through these broad zones which
expands both the scale and potential for the system.
To date, the Legacy Minerals exploration team has completed 1546m of drilling at Harden and has
budgeted for over 5000m across the project. This gives the Company significant room to expand on the
discovery.
Drill planning for the next stages at Harden is well underway and expected to start after receipt of all
pending assays and the completion of the upcoming drill campaign at the Bauloora Mine prospect.”
1
See Legacy Minerals Holdings ASX announcement, dated 23 September 2021
ACN 622 746 187
Level 7, 1 Margaret Street Sydney
ASX: LGM
Page 1 of 12
www.legacyminerals.com.au
Figure 1: Cross Section showing interpreted veins and mineralised halo (0.5g/t Au cut-off grade)
Page 2 of 12 | ACN 622 746 187
Level 7, 1 Margaret Street Sydney
www.legacyminerals.com.au
ASX: LGM
Figure 2: Cross Section showing interpreted veins and mineralised halo (0.2g/t Au cut-off grade)
Page 3 of 12 | ACN 622 746 187
Level 7, 1 Margaret Street Sydney
www.legacyminerals.com.au
ASX: LGM
Figure 3. Plan of Harden Gold Mine Prospect drill collars and hole traces
Harden Gold Mine Prospect - RC Drilling
The mineralised zones display similar characteristics as those seen in the previously returned high-grade
results of drill hole RC21HN005 (2m at 19.09 g/t Au). These characteristics include quartz veining with
abundant pyrite and minor amounts of galena and sphalerite. These mineralised zones are associated with
broader chlorite-sericite-pyrite alteration.
Hole RC21HN006 aimed to test the potential size of the remnant orebody left unmined in the western
portion of the Harden Gold Mine workings. Mineralisation is open along strike (east-west), down dip, and
to surface. Assay results from the drill hole shows gold mineralisation parallel to the historical workings.
Drilling intercepted historical workings from 81m to 85m with subsequent drilling difficulties occurring and
the early termination of the hole in mineralisation (1m at 2.77g/t Au). The stoped ground in this area is
interpreted to be backfilled. The drill hole results, combined with visual observations of coarse gold,
indicate a nugget effect on gold distribution.
Hole RC21HN003 is the deepest hole to date testing along strike of the Harden Gold Mine. Broad zones of
gold mineralisation were intercepted between 120m and 141m. Mineralisation is open along strike (eastwest) and down dip.
The width of the zones intercepted confirm the potential for broad lower grade gold mineralisation to
surround high-grade veins and provides increased encouragement for the future testing of the downplunge targets of the Harden Gold Mine.
Page 4 of 12 | ACN 622 746 187
Level 7, 1 Margaret Street Sydney
www.legacyminerals.com.au
ASX: LGM
About the Harden Project
The Harden Project encompasses several historical high-grade gold mines in a mineral district that has
produced >460,000 oz of gold from alluvial and hard rock mining. The historical mines within Legacy
Minerals’ Harden tenement are the largest hard rock mines in the district, producing a combined total of
~75,000 oz Au at an average grade of 28.6g/t Au – all before 1919. There are two main strikes of mine in
the tenement area – the historical Harden Gold Mine corridor and McMahons Reef Gold mine corridor.
The Project presents an advanced-stage brownfields exploration opportunity. Historical high-grade drill
intersects at the Harden Gold mine area returned a best intercept of 3m @ 10.5g/t Au from 20m and at the
southern McMahons Reef Gold Mine 3.6m @ 21.7g/t Au from 115m.
Figure 4: Overview showing the Harden Exploration Licences
Approved by the board of Legacy Minerals Holdings Limited.
For more information:
Chris Byrne
CEO & Managing Director
chris.byrne@legacyminerals.com.au
+61 (0) 409 392 326
Victoria Humphries
Media & Investor Relations
victoria@nwrcommunications.com.au
+61 (0) 431 151 676
Page 5 of 12 | ACN 622 746 187
Level 7, 1 Margaret Street Sydney
www.legacyminerals.com.au
ASX: LGM
About Legacy Minerals
Since 2017, Legacy Minerals has been involved in the acquisition and exploration of gold, copper, and basemetal projects in the prospective Lachlan Fold Belt in New South Wales. The Company has five tenements –
the Cobar Project (EL8709 and EL9256), Harden Project (EL8809 and EL9257), Bauloora Project (EL8994),
Fontenoy Project (EL8995) and Rockley Project (EL8296). All of Legacy Minerals’ projects are 100% owned
and present significant discovery opportunities for gold, copper and base-metal mineralisation.
Figure 5: Legacy Minerals’ Tenements, Lachlan Fold Belt NSW
Information in this announcement is extracted from the Company’s Prospectus dated 28 July 2021 lodged as a market announcement
on 9 September 2021. The Company confirms that it is not aware of any new information that materially affects the information included
in the original market announcement and that all material assumptions and technical parameters underpinning the estimates in the
relevant market announcement continue to apply and have not materially changed.
This announcement contains certain forward-looking statements. Forward looking statements are only predictions and are subject to
risks, uncertainties and assumptions which are outside of the control of Legacy Minerals Holdings Limited (LGM). These risks,
uncertainties and assumptions include commodity prices, currency fluctuations, economic and financial market conditions,
environmental risks and legislative, fiscal or regulatory developments, political risks, project delay, approvals and cost estimates. Actual
values, results or events may be materially different to those contained in this announcement. Given these uncertainties, readers are
cautioned not to place reliance on forward-looking statements. Any forward-looking statements in this announcement reflect the views of
LGM only at the date of this announcement. Subject to any continuing obligations under applicable laws and ASX Listing Rules, LGM
does not undertake any obligation to update or revise any information or any of the forward-looking statements in this announcement to
reflect changes in events, conditions or circumstances on which any forward-looking statements is based.
COMPETENT PERSONS STATEMENT The information in this report that relates to Exploration Targets, Exploration Results, Mineral
Resources or Ore Reserves is based on information compiled by Thomas Wall, a Competent Person who is a Member of the Australian
Institute of Geoscientists. Mr Wall is the Technical Director is a full-time employee of Legacy Minerals Limited and a shareholder, who
has sufficient experience that is relevant to the style of mineralisation and type of deposit under consideration and to the activity being
undertaken to qualify as a Competent Person as defined in the 2012 edition of the Australasian Code for Reporting of Exploration
Results, Mineral Resources and Ore Reserves. Mr Wall consents to the inclusion in the report of the matters based on his information in
the form and context in which it appears.
Page 6 of 12 | ACN 622 746 187
Level 7, 1 Margaret Street Sydney
www.legacyminerals.com.au
ASX: LGM
Table 1. Harden Project, Harden Gold Mine Prospect drill hole assay results
Significant intervals defined using >=0.2g/t Au, >=1m downhole width, <=1m internal waste and >=1g/t Au, >=1m downhole width, <=1m
internal waste. All intercepts are down hole widths. Collar location and orientation information coordinates are MGA Zone 55, AHD RL. See
Appendix 1 for additional details.
Above 0.2g/t Au cut-off. NSR = No significant results
Hole ID
Interval
From (m)
To (m)
Width (m)
RC21HN001
RC21HN002
Drill hole Collar Information
Au (g/t)
NSR
Easting
627433
Northing
6178285
RL
419
Depth (m)
138
Dip
70
Azimuth
200
628193
6177956
433.6456
204
71
196
628188.1
6177958
433.65
166
50
193
628031.3
6178020
429
144
65
180
628028
6178021
428.72
85
50
200
Awaiting assays
110
111
1
0.2
120
129
9
0.56
and
133
141
8
0.38
incl.
133
137
4
0.51
and
146
148
2
0.3
and
163
164
1
0.47
and
186
187
1
0.22
RC21HN004
97
98
1
0.41
and
143
144
1
0.64
and
150
151
1
0.67
RC21HN005
110
115
5
7.81
incl.
111
113
2
19.09
Incl.
111
112
1
32.80
and
133
138
5
1.47
incl.
RC21HN006
134
77
135
85
1
8
6.24
2.45
incl.
79
82
3
4.62
RC21HN007
Awaiting assays
RC21HN008
Awaiting assays
RC21HN009
Awaiting assays
RC21HN010
Awaiting assays
RC21HN011
Awaiting assays
RC21HN003
and
Appendix 1 – JORC Code, 2021 Edition Table 1
Section 1 Sampling Techniques and Data
Criteria
JORC Code Explanation
Commentary
Nature and quality of sampling (e.g., cut
channels, random chips, or specific specialised
industry standard measurement tools
appropriate to the minerals under investigation,
such as down hole gamma sondes, or handheld
XRF instruments, etc). These examples should not
be taken as limiting the broad meaning of
sampling.
Include reference to measures taken to ensure
sample representivity and the appropriate
calibration of any measurement tools or systems
used.
RC Sampling: All samples from the RC drilling are taken as 1m
samples for laboratory assay. Samples are collected using cone or
riffle splitter. Geological logging of RC chips is completed at site
with representative chips being stored in drill chip trays. Magnetic
susceptibility was recorded from the green bulk bag for each meter
by a KT-10 mag sus meter.
Sampling
Techniques
RC drilling was undertaken by Durock Drilling Pty Ltd
RC Sampling: Samples are taken on a one metre basis and collected
using uniquely numbered calico bags. The remaining material for
that metre is collected and stored in a green plastic bag marked
with that specific metre interval. The cyclone is cleaned with
compressed air after each plastic and calico sample bag is removed.
If wet sample or clays are encountered then the cyclone is opened
and cleaned manually and with the aid of a compressed air gun. A
blank sample is inserted at the beginning of each hole, and a
duplicate sample is taken every 50th sample. A certified sample
standard is also added according to geology, but at no more than
1:50 samples. The RC samples are then assayed at a certified
assay laboratory, ALS Laboratories.
Geological logging of RC chips is completed at site with
representative chips being stored in drill chip trays. Downhole
surveys of dip and azimuth are conducted using a single shot
camera every 30m, and using a downhole Gyro when required, to
detect deviations of the hole from the planned dip and azimuth.
The drill‐hole collar locations are recorded using a hand‐held GPS,
which has an accuracy of +/‐ 5m. All drill‐hole collars may be
surveyed to a greater degree of accuracy using a certified surveyor
at a later date.
An Olympus Vanta pXRF is used to systematically analyse the RC
sample onsite. One reading is taken per metre with field
calibration of the pXRF instrument using standards periodically
performed (usually daily).
The handheld pXRF results are only used for preliminary
assessment of element compositions, prior to the receipt of assay
results from the certified laboratory.
Sampling
Techniques
Drilling
techniques
Aspects of the determination of mineralisation
that are Material to the Public Report. In cases
where ‘industry standard’ work has been done
this would be relatively simple (e.g. ‘reverse
circulation drilling was used to obtain 1 m
samples from which 3 kg was pulverised to
produce a 30 g charge for fire assay’). In other
cases more explanation may be required, such as
where there is coarse gold that has inherent
sampling problems. Unusual commodities or
mineralisation types (e.g. submarine nodules)
may warrant disclosure of detailed information.
The holes were geologically logged and the magnetic susceptibility
was recorded from the calico bag for each meter by a KT-10 mag
sus meter.
Drill type (e.g. core, reverse circulation, open‐
hole hammer, rotary air blast, auger, Bangka,
sonic, etc) and details (e.g. core diametre, triple
or standard tube, depth of diamond tails,
facesampling bit or other type, whether core is
oriented and if so, by what method, etc).
RC Sampling: The RC drilling uses a 144 mm diameter face hammer
tool. High-capacity air compressors on the drill rig are used to
ensure a continuously sealed and high‐pressure system during
drilling to maximise the recovery of the drill cuttings, and to ensure
chips remain dry to the maximum extent possible.
RC Drilling – the total sample (~20-30kg) is delivered via cyclone
into a large plastic bag which is retained for future use if required.
The RC samples were transported to ALS Laboratory in Orange for
assaying. Pulverize up to 3kg of raw sample. QC specification of 85%
<75μm. Samples greater than 3kg are split prior to pulverizing and
the remainder retained. Gold was determined by fire assay fusion
of a 30g charge with an AAS analytical finish. The lower detection
limit for gold is 0.01 ppm, which is believed to be an appropriate
detection level.
Method of recording and assessing core and chip
sample recoveries and results assessed.
Drill sample
recovery
Measures taken to maximise sample recovery
and ensure representative nature of the samples.
Whether a relationship exists between sample
recovery and grade and whether sample bias
may have occurred due to preferential loss/gain
of fine/coarse material.
Logging
Whether core and chip samples have been
geologically and geotechnically logged to a level
of detail to support appropriate Mineral
Resource estimation, mining studies and
metallurgical studies.
Whether logging is qualitative or quantitative in
nature. Core (or costean, channel, etc)
photography.
The total length and percentage of the relevant
intersections logged.
If core, whether cut or sawn and whether
quarter, half or all core taken.
If non‐core, whether riffled, tube sampled, rotary
split, etc and whether sampled wet or dry.
For all sample types, the nature, quality and
appropriateness of the sample preparation
technique.
Sub‐sampling
techniques and
sample
preparation
Quality control procedures adopted for all
subsampling stages to maximise representivity of
samples.
Measures taken to ensure that the sampling is
representative of the in-situ material collected,
including for instance results for field
duplicate/second‐half sampling.
Whether sample sizes are appropriate to the
grain size of the material being sampled.
Quality of
assay data and
laboratory
tests
The nature, quality and appropriateness of the
assaying and laboratory procedures used and
whether the technique is considered partial or
total.
For geophysical tools, spectrometres, handheld
XRF instruments, etc, the parametres used in
determining the analysis including instrument
RC Sampling: RC samples are visually checked for recovery,
moisture and contamination. Geological logging is completed at site
with representative RC chips stored in chip trays. Sample weights
were recorded on site using digital scales for each calico sample.
RC Sampling: Samples are collected using cone or riffle splitter.
Geological logging of RC chips is completed at site with
representative chips being stored in drill chip trays. Sample sizes
were monitored and the splitter was regularly agitated to reduce
the potential for sample contamination
To date, no sample recovery issues have yet been identified that
would impact on potential sample bias in the competent fresh rocks
that host the mineralised sulphide intervals
There is no known relationship between sample recovery and grade
Geological logging is carried out on all drill holes with lithology,
alteration, mineralisation, structure and veining recorded.
Logging of RC samples records lithology, mineralogy, mineralisation,
structures, weathering, colour and other noticeable features. Chip
trays were photographed in wet form.
All drill holes are geologically logged in full and lithogeochemical
information is collected by the field XRF unit. The data relating to
the elements analysed is used to determine further information
regarding the rock composition.
NA
RC samples are collected using acone or riffle splitter when
available. Geological logging of RC chips is completed at site with
representative chips being stored in drill chip trays.
RC Sampling: Sample preparation for RC chips follows a standard
protocol. If a sample is wet or damp it is recorded. Most samples
were dry.
Samples were delivered by Legacy Minerals Holdings personnel to
ALS Minerals Laboratory, Orange NSW. Sample preparation will
comprise of an industry standard of drying, jaw crushing and
pulverising to -75 microns (85% passing) (ALS code PUL-23).
Pulverisers are washed with QAQC tests undertaken (PUL-QC).
Samples are dried, crushed and pulverized to produce a
homogenous representative sub‐sample for analysis.
Quality control procedures include submission of Certified
Reference Materials (standards) and duplicates with each sample
batch. QAQC results are routinely reviewed to identify and resolve
any issues.
RC Sampling: Field QC procedures maximise representivity of RC
samples and involve the use of certified reference material as assay
standards, along with blanks, duplicates and barren washes.
Duplicate RC samples are captured using two separate sampling
apertures on the splitter approximately every 50m.
The sample sizes are considered to be appropriate to correctly
represent gold mineralisation and associated geology based on: the
style of mineralisation (quartz with minor sulphides), the thickness
and consistency of the intersections and the sampling
methodology.
All samples were analysed by ALS Minerals
Gold is determined using a 30g charge. The resultant prill is
dissolved in aqua regia with gold determined by flame AAS.
An Olympus Vanta pXRF is used to systematically analyse the RC
sample onsite. One reading is taken per metre. Field calibration of
the XRF instrument using standards is periodically performed
(usually daily).
make and model, reading times, calibrations
factors applied and their derivation, etc.
Nature of quality control procedures adopted
(e.g. standards, blanks, duplicates, external
laboratory checks) and whether acceptable levels
of accuracy (i.e. lack of bias) and precision have
been established.
The verification of significant intersections by
either independent or alternative company
personnel.
The use of twinned holes.
Documentation of primary data, data entry
procedures, data verification, data storage
(physical and electronic) protocols.
Verification of
sampling and
assaying
Discuss any adjustment to assay data.
Location of
data points
Accuracy and quality of surveys used to locate
drill holes (collar and down‐hole surveys),
trenches, mine workings and other locations used
in Mineral Resource estimation.
Specification of the grid system used.
Quality and adequacy of topographic control.
Data spacing
and
distribution
Orientation of
data in relation
to geological
structure
Sample
security
Data spacing for reporting of Exploration Results.
Whether the data spacing and distribution is
sufficient to establish the degree of geological
and grade continuity appropriate for the Mineral
Resource and Ore Reserve estimation
procedure(s) and classifications applied. Whether
sample compositing has been applied.
Whether sample compositing has been applied.
Whether the orientation of sampling achieves
unbiased sampling of possible structures and the
extent to which this is known, considering the
deposit type.
If the relationship between the drilling
orientation and the orientation of key
mineralised structures is considered to have
introduced a sampling bias, this should be
assessed and reported if material.
The measures taken to ensure sample security.
The handheld pXRF results are only used for preliminary
assessment of element compositions, prior to the receipt of assay
results from the certified laboratory.
Laboratory QAQC involves the use of internal lab standards using
certified reference material (CRMs), blanks and pulp duplicates as
part of in‐house procedures. The Company also submits a suite of
CRMs, blanks where appropriate and selects appropriate samples
for duplicates.
Sample preparation checks for fineness are performed by the
laboratory to ensure the grind size of 85% passing 75μm is being
attained.
Significant intersections are verified by the Company’s technical
staff.
No twinned holes have been planned for the current drill
programme.
Primary data is captured onto a laptop through excel and using
Datashed software and includes geological logging, sample data and
QA/QC information. This data, together with the assay data, is
stored both locally and entered into the LGM central online
database which is managed by external consultants.
All primary assay data is received from the laboratory as electronic
data files which are imported into sampling database with
verification procedures in place. QAQC analysis is undertaken for
each laboratory report
No adjustments or calibrations will be made to any primary assay
data collected for the purpose of reporting assay grades and
mineralised intervals. For the geological analysis, standards and
recognised factors may be used to calculate the oxide form assayed
elements, or to calculate volatile free mineral levels in rocks.
RC Drilling - A handheld Garmin GPSmap 65 was used to pick up
collars with an averaged way point accuracy of 1m. Downhole
surveys are conducted using a single shot camera approximately
every 30m or downhole Gyro during drilling to record and monitor
deviations of the hole from the planned dip and azimuth.
The grid system used is GDA94, MGA Zone 55.
Using government data topography and 2017 DTM data. A
topographic surface has been created using this elevation data
The results are at an early stage, reconnaissance drilling. The
spacing and distribution of holes is not relevant to the drilling
programs which are at this exploration stage rather than definition
drilling.
The completed drilling at the Project is not sufficient to establish
the degree of geological and grade continuity to support the
definition of Mineral Resource and Reserves and the classifications
applied under the 2012 JORC code.
No compositing has been applied to the exploration results.
The drill holes are drilled to intersect the modelled mineralised
zones at as near perpendicular orientation possible (unless
otherwise stated). Drilling suggests a broadly sub vertical geometry,
however the orientation of key structures may be locally variable
and any relationship to mineralisation has yet to be identified.
Estimated true width intervals at this early stage of drilling are
possibly ~70% of downhole lengths
All samples are bagged into tied calico bags, before being grouped
into polyweave bags and transported to ALS Minerals Laboratory in
Orange by Legacy Minerals personnel. All sample submissions are
documented via ALS tracking system with results reported via email
Sample pulps are returned to site and stored for an appropriate
length of time.
Audits or
reviews
The results of any audits or reviews of sampling
techniques and data.
The Company has in place protocols to ensure data security.
Sampling techniques and procedures are regularly reviewed
internally, as is data. To date, no external audits have been
completed on the drilling programme.
Section 2 Reporting of Exploration Results
(Criteria in this section apply to all succeeding section)
Criteria
Mineral
Tenement and
Land Status
JORC Code Explanation
Commentary
Type, name/reference number, location and
ownership including agreements or material
issues with third parties including joint
ventures, partnerships, overriding royalties,
native title interests, historical sites,
wilderness or national park and
environmental settings.
The Harden Project is comprised of two granted Exploration
Licenses: EL8809 and EL9257. Both licenses are owned 100% by
Legacy Minerals Pty Ltd (a fully owned subsidiary of Legacy Minerals
Holdings Limited). There are no royalties or encumbrances over the
tenement areas.
The security of the tenure held at the time of
reporting along with any known impediments
to obtaining a licence to operate in the area.
Exploration
Done by Other
Parties
Geology
Drill hole
Information
Data
aggregation
methods
Relationship
between
mineralisation
widths and
Acknowledgment and appraisal of
exploration by other parties.
Deposit type, geological setting and style of
mineralisation
A summary of all information material to the
understanding of the exploration results
including tabulation of the following
information for all Material drill holes:
• Easting and northing of the drill hole collar
•Elevation or RL (Reduced Level – elevation
above sea level in metres) of the drill hole
collar
• Dip and azimuth of the hole
• Down hole length and interception depth
• Hole length
If the exclusion of this information is justified
on the basis that the information is not
Material and this exclusion does not detract
from the understanding of the report, the
Competent Person should clearly explain why
this is the case.
In reporting Exploration Results, weighting
averaging techniques, maximum and/or
minimum grade truncations (e.g. cutting of
high grades) and cut‐off grades are usually
Material and should be stated.
Where aggregated intercepts incorporate
short lengths of high grade results and longer
lengths of low grade results, the procedure
used for such aggregation should be stated
and some typical examples of such
aggregations should be shown in detail.
The assumptions used for any reporting of
metal equivalent values should be clearly
stated.
These relationships are particularly important
in the reporting of exploration results. If the
geometry of the mineralisation with respect
to the drill hole angle is known, its nature
The land is primarily freehold land. There are no native title
interests in the license area.
The transmitter and receiver electrode positions are located to
hand-held GPS accuracy, generally +-3m (UTM projection GDA94
Zone 55).
RC Drilling - The RC drilling was planned by Legacy Minerals
Holdings exploration staff in consultation with drilling contractor
Durock Drilling.
The Harden Gold Mine prospect is hosted within the Silurian Young
Granodiorite. The prospect is prospective for high-grade gold
mineralisation hosted within low-sulphide quartz veining of similar
style to that which has been historically mined in the area.
See Table 2 in the body of the article
N/A
Exploration results reported for uncut gold grades, grades
calculated by length weighted average
Reported intercepts (>0.2g/t Au) are calculated using a broad lower
cut of 0.2g/t Au although grades lower than this may be present
internally (internal dilution).
No top cut has been used.
No metal equivalents reported
The mineralisation is structurally complex. Assay intersections are
reported as down hole lengths. Drill holes are planned as
perpendicular as possible to intersect the geological targets. At this
early stage of drilling and geological knowledge of the project true
intercept
lengths
Diagrams
Balanced
Reporting
Other
substantive
exploration
data
Further Work
should be reported. If it is not known and
only the down hole lengths are reported,
there should be a clear statement to this
effect.
Appropriate maps and sections (with scales)
and tabulations of intercepts should be
included for any significant discovery being
reported. These should include, but not be
limited to a plane view of drill hole collar
locations and appropriate sectional views.
Where comprehensive reporting of all
Exploration Results is not practical
representative reporting of both low and high
grades and/or widths should be practiced to
avoid misleading reporting of Exploration
Results.
widths are estimated to be approximately 70% of down hole
intervals.
Other exploration data, if meaningful and
material, should be reported including (but
not limited to): geological observation;
geophysical survey results; geochemical
survey results; bulk samples – size and
method of treatment; metallurgical test
results; bulk density, groundwater,
geotechnical and rock characteristics;
potential deleterious or contaminating
substances.
The nature and scale of planned further work
(e.g. tests for lateral extensions or depth
extensions or large – scale step – out
drilling).Diagrams clearly highlighting the
areas of possible extensions, including the
main geological interpretations and future
drilling areas, provided this information is not
commercially sensitive.
All material or meaningful data collected has been reported.
A
Share your feedback
Discover