Announcement PDF ASX Announcement 26 September 2024 Bauloora drill results up to 468g/t Ag, 3.8g/t Au, 22% Zn-Pb Compelling gold and silver drilling results at new Prospects • • High-grade and shallow assays up to 468g/t Ag, 3.8g/t Au and 22.8% Zn+Pb. Multiple vein trends were highlighted for future follow-up drill testing. New discovered mineralised veins trends Moonlite (New Area): • 4.1m at 5.0g/t AuEq from 149m (0.61g/t Au, 17.5g/t Ag, 5.8% Zn, 4.3% Pb, 0.2% Cu) incl. o 1m at 10.9g/t AuEq from 150m (1.2g/t Au, 44.8g/t Ag, 11.1% Zn, 11.8% Pb, 0.44% Cu) o within 14.1m at 2.13g/t AuEq from 141m (0.25g/t Au, 8.1g/t Ag, 2.3% Zn, 2% Pb and 0.1% Cu ML001 – no cut off) Ben Hall (New Area): • 24m at 0.5g/t Au from 70m incl. o 13.4m at 0.7g/t Au from 70.6m incl. o 2m at 3.33g/t Au from 76m (BH001). Breakout (New Area): • 4.3m at 3.2g/t AuEq from 106m (0.6g/t Au, 80.5g/t Ag, 2% Zn, 0.6% Pb, 0.3% Cu) incl. o 0.6m at 10.8g/t AuEq from 107.9m (0.5g/t Au, 468g/t Ag, 6.0% Zn, 1.3% Pb, 0.64% Cu) (BK002) Next Stages at the Bauloora Project • • Drilling was funded under the Phase 1 Earn-In of the $15M Bauloora Joint Venture with Newmont i. Upcoming drilling is planned in Q4 2024 to continue reconnaissance step out drill holes. • Other prospects and areas of interest include: Bluecap Prospect ii: • 13m at 3.6g/t AuEq from 57m, (13m at 1.7g/t Au, 6.7g/t Ag, 0.1% Cu, 4.2% Pb+Zn) incl. o 3.7m at 10.5g/t AuEq from 57.44m, (3.7m at 5.6g/t Au, 17.4g/t Ag, 0.3% Cu, 10.5% Pb+Zn) Management comment – Legacy Minerals CEO & Managing Director Christopher Byrne said: “The latest results have delivered shallow and high-grade hits up to 468g/t Ag, 22% Zn+Pb and 3.8g/t Au from wide-spaced reconnaissance drill testing. “This is encouraging as we’re confirming multiple vein trends with strong mineralisation that until now had never before been drill tested. The success at these targets further highlights the potential of the large anomalous areas that remain undrilled and the potential of the Bauloora system that remains open in all directions. “An exciting takeaway is the success rate of intercepting mineralisation on the Bauloora Project. Out of four previously undrilled prospects, three have returned promising results. The single hole into the fourth prospect, Marry Bugg, delivered over a 200m zone of alteration that provides further encouragement to the size of the mineral system at Bauloora and is supported by the widespread surface soil and rock chip anomalism. “We have another drilling campaign planned at Bauloora for later this year, and we look forward to providing further updates on the Project over the coming months.” 1 See ‘Endnotes’ on Page 18 for references. Page 1 of 18 | ABN 43 650 398 897 3/202 Russel Street Bathurst, 2795 www.legacyminerals.com.au ASX: LGM Page 2 of 18 Legacy Minerals Holdings Limited (ASX: LGM, “Legacy Minerals” or “the Company”) is pleased to provide an update on the drilling completed at the Bauloora Project (EL8995 and EL9464) in the Lachlan Fold Belt, NSW. Daimond Drilling Results On the Bauloora Project, eight diamond holes have been completed for a total of 1,437.1 metres. These tested four prospects defined by a combination of anomalous soil and rock chip geochemistry and geophysical signatures. The diamond drill holes have confirmed epithermal-style veins beneath elevated gold, silver, and pathfinder rock chip and soil geochemical results and mapped veins. Figure 1: Bauloora Project with recently completed drilling (red border) and previous drilling results over Sb in soil sampling and regional geology interpretation. SIGN UP TO LEGACY MINERALS’ INTERACTIVE INVESTOR HUB ASX: LGM Page 3 of 18 At the Ben Hall Prospect, two diamond drill holes, for a total of 315.6m, were completed which tested the 400m long zone of elevated gold and pathfinder elements defined in soil sampling with gold grades in rock chips returning up to 4.15g/t Au. BH001 intersected strong alteration from 66-95m and 134158m in association with epithermal veins. Intercepts reported include 24m at 0.5 g/t Au from 70m, including 13.4m at 0.7g/t Au from 70.6m. BH002 intercepted moderate alteration with lesser veins with no significant intercepts reported. Figure 2: Ben Hall Prospect, cross section showing BH001, looking NE showing significant intercepts (yellow) and surface sampling rock chip results. At the Moonlite Prospect, two diamond drill holes, for a total of 331m, were completed which tested the 400m long zone of elevated gold (up to 136ppb Au), silver and pathfinder elements defined in soil sampling. Rock chip sampling returned gold and silver grades up to 2.94g/t Au and 33.3g/t Ag. ML001 intersected strong alteration from start to end of hole with a 12.2m interval of epithermal vein and breccia from 142.8m downhole. Intercepts reported include 14.1m at 0.25g/t Au, 8.1g/t Ag, 2.3% Zn, 2% Pb and 0.1% Cu from 141m (uncut), including 4.1m at 0.61g/t Au, 17.5g/t Ag, 5.8% Zn, 4.3% Pb and 0.2% Cu from 149m. ML002 intersected a best result of 1.6m at 0.37g/t Au and 2.4g/t Ag from 64.4m. At the Breakout Prospect, two diamond drill holes, for a total of 309.4m, were completed which tested the 500m zone of elevated gold (up to 204ppb Au) and pathfinder elements defined in soil sampling. Rock chip sampling returned gold and silver grades up to 1.27g/t Au and 81.6g/t Ag. BK002 intersected moderate-strong alteration from 20-117m. Strong alteration was associated with the main epithermal vein zone intersected between 105.5-110.5m. Intercepts reported include 4.3m at 0.6g/t Au, 80.5g/t Ag, 2% Zn, 0.6% Pb and 0.3% Cu from 106m, including 0.6m at 0.5g/t Au, 468g/t Ag, 6.0% Zn, 1.3% Pb and 0.6% Cu from 107.9m. BK001 intersected alteration and anomalous gold from start of hole to approximately 140m. Strong alteration was associated with the two main epithermal vein zones intersected between approximately 28-37m and 102-108m. A number of anomalous zones were intercepted including 2.7m at 0.23g/t Au, 8.64g/t Ag, 1.62% Zn and 0.95% Pb from 105.3m. At the Bauloora East Prospect, a single diamond drill hole was completed to 150.5m. This drill hole tested the southernmost extent of the large 1,500m x 150m zone of elevated gold, base-metals and other pathfinder elements defined in soil sampling. Rock chip sampling has returned gold and silver grades up to 8.52g/t Au. Better intercepts reported include 1m at 10g/t Ag, 4.86% Zn and 1.73% Pb from 111.5m. SIGN UP TO LEGACY MINERALS’ INTERACTIVE INVESTOR HUB ASX: LGM Page 4 of 18 Figure 3: Moonlite Prospect, cross section showing ML001, looking north showing significant intercepts (yellow) and surface sampling rock chip results. Figure 14: Breakout Prospect, cross section showing BK002, looking north showing significant intercepts (yellow) and surface sampling rock chip results. At the Mary Bugg Prospect, a single diamond drill hole, for a total of 330.6m, was completed which tested a gold-silver bearing low sulphidation epithermal vein zone with elevated gold and pathfinder elements defined in soil and extensive rock chip sampling returning grades up to 8.29g/t Au and 933g/t Ag. Drilling intersected widespread pathfinder anomalism in association with alteration with better intercepts reported including 4.4m at 0.16g/t Au, 4.35g/t Ag, 1.4%Zn and 0.6% Pb from 186.6m. SIGN UP TO LEGACY MINERALS’ INTERACTIVE INVESTOR HUB ASX: LGM Page 5 of 18 About the Bauloora Project Legacy Minerals’ Bauloora Project is located in the Lachlan Fold Belt of New South Wales which is host to world-class copper-gold orebodies including the Cadia-Ridgeway, Northparkes, and Cowal Mines. In 2023, Newmont Exploration Pty Ltd entered into a Farm-In and Joint Venture on the Project iii. It covers a large hydrothermal alteration zone 27km2 in size, within which is an anomalous gold zone currently mapped to 15km2. Rock chip and soil samples collected by the Company from the Project area have highlighted several priority areas of anomalous precious metal values with highly anomalous values of epithermal pathfinders iv. The drilling of the first of these targets resulted in the discovery of the Bluecap Prospect returning 13m at 1.66g/t Au, 6.68g/t Ag, 0.14% Cu and 4.23% Pb+Zn from 57miv. 2F 3F Extensive epithermal alteration exists on the Project, including widespread zones of high-level chalcedonic veins, clay alteration and local sinter formations. The Project has seen very limited exploration drilling and the Company believes the results from work to date support the assessment that there is potential for the discovery of a low-sulphidation epithermal-style gold-silver deposit at the Bauloora Project. Figure 5: Regional setting of the Bauloora Project and major deposits in NSW v 4F SIGN UP TO LEGACY MINERALS’ INTERACTIVE INVESTOR HUB ASX: LGM Page 6 of 18 Approved by the Board of Legacy Minerals Holdings Limited. For more information: Investors: Chris Byrne CEO & Managing Director chris.byrne@legacyminerals.com.au +61 (0) 499 527 547 Media: Nicholas Read Read Corporate nicholas@readcorporate.com.au +61 (0) 419 929 046 DISCLAIMER AND PREVIOUSLY REPORTED INFORMATION Information in this announcement is extracted from reports lodged as market announcements referred to above and available on the Company’s website https://legacyminerals.com.au/. The Company confirms that it is not aware of any new information that materially affects the information included in the original market announcement and that all material assumptions and technical parameters underpinning the estimates in the relevant market announcement continue to apply and have not materially changed. This announcement contains certain forward-looking statements. Forward looking statements are only predictions and are subject to risks, uncertainties and assumptions which are outside of the control of Legacy Minerals Holdings Limited (LGM). These risks, uncertainties and assumptions include commodity prices, currency fluctuations, economic and financial market conditions, environmental risks and legislative, fiscal or regulatory developments, political risks, project delay, approvals and cost estimates. Actual values, results or events may be materially different to those contained in this announcement. Given these uncertainties, readers are cautioned not to place reliance on forward-looking statements. Any forward-looking statements in this announcement reflect the views of LGM only at the date of this announcement. Subject to any continuing obligations under applicable laws and ASX Listing Rules, LGM does not undertake any obligation to update or revise any information or any of the forward-looking statements in this announcement to reflect changes in events, conditions or circumstances on which any forward-looking statements is based. COMPETENT PERSON’S STATEMENT The information in this Report that relates to Exploration Targets, Exploration Results, Mineral Resources or Ore Reserves is based on information compiled by Thomas Wall, a Competent Person who is a Member of the Australian Institute of Geoscientists. Mr Wall is the Technical Director and a full-time employee of Legacy Minerals Pty Limited, the Company’s wholly-owned subsidiary, and a shareholder of the Company. Mr Wall has sufficient experience that is relevant to the style of mineralisation and type of deposit under consideration and to the activity being undertaken to qualify as a Competent Person as defined in the 2012 edition of the Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves. Mr Wall consents to the inclusion of the matters based on this information in the form and context in which it appears in this announcement. SIGN UP TO LEGACY MINERALS’ INTERACTIVE INVESTOR HUB ASX: LGM Page 7 of 18 About Legacy Minerals Legacy Minerals is an ASX listed public company that has been involved in the acquisition and exploration of gold, copper, and base-metal projects in NSW since 2017. The Company has eight projects that present significant discovery opportunities for shareholders. 0BAu-Ag Black Range (EL9464, EL9589) Extensive low-sulphidation, epithermal system with limited historical exploration. Epithermal occurrences across 30km of strike. 1BCu-Au Drake (EL6273, EL9616, ELA6642) Large caldera (~150km2) with similar geological characteristics to other major pacific rim low-sulphidation deposits. 2BCu-Au Rockley (EL8926) 3B Au-Cu (Pb-Zn) Cobar (EL9511) Helix JV Prospective for porphyry Cu-Au and situated in the Macquarie Arc Ordovician host rocks with historic highgrade copper mines that graded up to 23% Cu. Undrilled targets next door to the Peak Gold Mines. Several priority geophysical anomalies and gold in lag up to 1.55g/t Au. Au-Ag Bauloora (EL8994, EL9464) Newmont JV One of NSW’s largest low-sulphidation, epithermal systems with a 27km2 epithermal vein field. Cu-Au Glenlogan (EL9614) S2 Resources JV Large, undrilled magnetic anomaly underneath Silurian cover located 55kms from Cadia Valley. 6B Au Harden (EL9657) Large historical high-grade quartz-vein gold mineralisation. Drilling includes 3.6m at 21.7g/t Au 116m and 2m at 17.17g/t Au from 111m. Au-Cu Fontenoy (EL8995) Earth AI Alliance An 8km long zone of Au and Cu anomalism defined in soil sampling and drilling. Significant drill intercepts include 79m at 0.27% Cu from 1.5m. 4BCCu-Au Thomson (EL9190, EL9194, ELA6777) Prospective for intrusion-related gold and copper systems the project contains numerous ‘bullseye’ magnetic and gravity anomalies that remain untested. Figure 6: Location of Legacy Minerals’ Projects in NSW, Australia vi 5F SIGN UP TO LEGACY MINERALS’ INTERACTIVE INVESTOR HUB ASX: LGM Page 8 of 18 Appendix 1 - Highlight Drill Results Table 1. Drill hole collar details for recently completed diamond core drill holes. Hole ID Easting (MGA94/55) Northing (MGA94/55) RL (m) Dip Azimuth (True North) Depth (m) BE001 590122 6176686 430 70 130 150.5 BH001 589425 6175855 465 60 120 183.5 BH002 589336 6175950 449 60 300 150.5 BK001 589734 6175371 470 60 90 152.9 BK002 589652 6175279 449 60 270 156.5 ML001 589850 6175342 473 60 270 150.5 ML002 589955 6176607 432 60 90 165.1 MB001 588920 6175601 335 60 90 330.6 Table 2. Significant intervals from latest drilling. Hole ID MB001 BE001 BH001 From (m) To (m) Width (m) Au (g/t) Ag (g/t) Zn (%) Pb (%) Cu (%) 94.7 95.7 1 0.05 3.33 0.25 0.12 0.01 111 113 2 0.01 1.24 0.63 0.84 0.00 122 124 2 0.00 1.63 0.10 0.39 0.00 147 148 1 0.35 0.73 0.40 0.05 0.01 186.6 191 4.4 0.16 4.35 1.42 0.63 0.06 197 198 1 0.02 0.56 1.00 0.03 0.01 201 202 1 0.01 4.48 0.02 0.58 0.01 276 278 2 0.01 0.51 0.29 0.04 0.00 5 10 5 0.00 0.91 0.05 0.33 0.01 11 12 1 0.19 3.95 0.08 0.19 0.04 13 14 1 0.01 2.50 0.11 0.18 0.03 16 18 2 0.01 1.60 0.16 0.15 0.03 20 24 4 0.01 0.89 0.07 0.24 0.03 61 62 1 0.04 17.45 0.00 0.23 0.00 65 66 1 0.01 7.92 0.25 1.00 0.00 111.5 112.5 1 0.03 9.96 4.86 1.73 0.00 1.4 2 0.6 0.01 33.40 0.01 0.01 0.00 52 54 2 0.10 0.70 0.02 0.01 0.00 70 94 24 0.49 1.52 0.26 0.07 0.00 108.3 109.55 1.25 0.23 4.68 0.03 0.41 0.00 120.4 120.6 0.2 0.17 0.81 0.04 0.05 0.00 126 128 2 0.41 1.31 0.13 0.02 0.01 143 144 1 0.04 17.85 0.30 0.87 0.00 BH002 BK001 NSR 11.7 12 0.3 0.15 0.29 0.00 0.01 0.01 27.7 32 4.3 0.36 4.40 0.03 0.13 0.05 SIGN UP TO LEGACY MINERALS’ INTERACTIVE INVESTOR HUB ASX: LGM Page 9 of 18 BK002 ML001 ML002 36 37 1 0.18 1.18 0.01 0.06 0.01 54 55 1 0.02 3.93 0.08 0.23 0.10 88 89 1 0.03 2.26 0.16 0.14 0.17 93 94.1 1.1 0.02 0.81 0.25 0.05 0.03 105.3 108 2.7 0.23 8.64 1.62 0.95 0.08 110 113 3 0.05 1.37 0.23 0.12 0.04 114 115 1 0.18 1.24 0.13 0.13 0.04 116 116.7 0.7 0.41 13.70 0.07 0.20 0.02 124 126 2 0.01 0.59 0.24 0.02 0.03 128 130 2 0.05 0.81 0.27 0.07 0.02 134 138 4 0.01 0.51 0.10 0.05 0.00 75 76 1 0.02 0.67 0.48 0.05 0.03 106 110.3 4.3 0.56 80.49 1.97 0.59 0.29 41 42 1 0.00 0.15 0.30 0.00 0.00 141 145 4 0.19 7.19 1.73 1.82 0.09 147 155.1 8.1 0.34 10.46 3.16 2.57 0.14 56.4 57.4 1 0.42 1.62 0.01 0.01 0.06 64.4 66 1.6 0.37 2.40 0.02 0.00 0.02 Significant intervals defined using >=0.1g/t Au or >=10g/t Ag or >=0.25% Cu, >=0.25% Pb+Zn, >=1m downhole width, and <=1m internal waste. All intercepts are down hole widths only, true widths are not calculated. Collar location and orientation information coordinates are GDA94/MGA Zone 55, AHD RL. See Appendix 1 for additional details. SIGN UP TO LEGACY MINERALS’ INTERACTIVE INVESTOR HUB ASX: LGM Page 10 of 18 Appendix 2 – JORC Code, 2021 Edition Table 1 Section 1 Sampling Techniques and Data Criteria JORC Code Explanation Commentary Nature and quality of sampling (e.g., cut channels, random chips, or specific specialised industry standard measurement tools appropriate to the minerals under investigation, such as down hole gamma sondes, or handheld XRF instruments, etc). These examples should not be taken as limiting the broad meaning of sampling. Core size was PQ core (diameter: 85mm) to fresh rock and HQ core (diameter: 63.5mm) to end of hole (EOH). LGM used a reputable drilling contractor, Ophir Drilling, with a suitable rig. Diamond drill core provide a high-quality sample that is logged for lithological, structural, geotechnical, and other attributes. Subsampling of the core is carried out as per industry best practice. Downhole surveys of dip and azimuth are conducted using a single shot camera every 30m, and using a downhole Gyro when required, to detect deviations of the hole from the planned dip and azimuth. The drill‐hole collar locations are recorded using a hand‐held GPS, which has an accuracy of +/‐ 5m. All drill‐ hole collars may be surveyed to a greater degree of accuracy using a certified surveyor at a later date. An Olympus Vanta pXRF is used to spot analyse the drill core onsite. Readings are taken to help identify minerals and alteration with field calibration of the pXRF instrument using standards periodically performed. The handheld pXRF results are only used for preliminary assessment of element compositions, prior to the receipt of assay results from the certified laboratory. Sampling Techniques Include reference to measures taken to ensure sample representivity and the appropriate calibration of any measurement tools or systems used. The drill core was orientated using suitable core orientation tool by the drilling contractor with LGM staff supervision. These orientations are extended onto the remainder of the core and meter marks for logging. The visible structural features (veins, bedding, foliation, faults) are measured against the core orientation marks. The drill core was cut in half, and assayed at a certified assay laboratory, ALS Laboratories. Core is prepared for analysis by cutting along the longitudinal line and then samples are numbered as per the pre-designed cut-sheet. The core is selectively sampled down the drill string at 1m nominal intervals across the mineralised zones, unless selected geological or mineralisation boundaries. A certified sample standard is inserted a minimum 1:50 samples. Standards may also be added according to geology. Where core was incompetent due to being transported cover or weathered rock, representative samples were collected along the axis of the core. SIGN UP TO LEGACY MINERALS’ INTERACTIVE INVESTOR HUB ASX: LGM Page 11 of 18 Aspects of the determination of mineralisation that are Material to the Public Report. In cases where ‘industry standard’ work has been done this would be relatively simple (e.g. ‘reverse circulation drilling was used to obtain 1m samples from which 3 kg was pulverised to produce a 30 g charge for fire assay’). In other cases more explanation may be required, such as where there is coarse gold that has inherent sampling problems. Unusual commodities or mineralisation types (e.g., submarine nodules) may warrant disclosure of detailed information. The drill core was cut by LGM staff. Samples were transported to ALS Laboratory in Orange for assaying. Samples are crushed to 6mm and then pulverized to 85% passing 75 microns. A 50g split of the sample was fired assayed for gold. The lower detection limit for gold is 0.002 ppm, which is believed to be an appropriate detection level. All other elements including copper and base metals (total 48 element suite) are analysed using a 4-acid acid digest and an ICP finish (ALS code: ME-MS61 + Au-AA21 + HgMS42). Assay standards, blanks and duplicates were analysed as part of the standard laboratory analytical procedures. Company standards were introduced into the sampling at a ratio minimum of 1 standard for every 50 samples. Sample length: Core is sampled in 0.2m to 2m sample interval lengths except for minor changes due to geological or mineralisation boundaries. Pulps are retained by LGM for potential follow-up analysis. Drilling techniques Drill type (e.g., core, reverse circulation, open‐hole hammer, rotary air blast, auger, Bangka, sonic, etc) and details (e.g. core diametre, triple or standard tube, depth of diamond tails, face sampling bit or other type, whether core is oriented and if so, by what method, etc). Method of recording and assessing core and chip sample recoveries and results assessed. Drill sample recovery Measures taken to maximise sample recovery and ensure representative nature of the samples. Whether a relationship exists between sample recovery and grade and whether sample bias may have occurred due to preferential loss/gain of fine/coarse material. Diamond drilling using industry standard techniques. HQ core (diameter: 63.5mm) to end of hole (EOH). Core recoveries were recorded during drilling and reconciled during the core processing and geological logging. Core is measured and marked after each drill run using wooden blocks calibrating depth. Adjusting rig procedures as necessary including, drilling rate, run length and fluid pressure to maintain sample integrity. To date, minimal sample recovery issues have been identified that would impact on potential sample bias in the competent fresh rocks that host the mineralised intervals. Systematic geological and geotechnical logging was undertaken. Data collection where appropriate includes: • Nature and extent of lithologies. Logging Whether core and chip samples have been geologically and geotechnically logged to a level of detail to support appropriate Mineral Resource estimation, mining studies and metallurgical studies. • Relationship between lithologies. • Amount and mode of occurrence of ore minerals. • Location, extent and nature of structures such as bedding, cleavage, veins, faults etc. Structural data (alpha & beta) are recorded for orientated core. • Geotechnical data is collected as required including recovery, RQD, fracture frequency, qualitative IRS, microfractures, veinlets and number of defect sets. For some geotechnical SIGN UP TO LEGACY MINERALS’ INTERACTIVE INVESTOR HUB ASX: LGM Page 12 of 18 holes the orientation, nature of defects and defect fill may be recorded. • Representative ulk density by Archimedes principle may be taken. Whether logging is qualitative or quantitative in nature. Core (or costean, channel, etc) photography. The total length and percentage of the relevant intersections logged. • Magnetic susceptibility recorded at 1m intervals for some holes as an orientation and alteration characterisation tool. Logging records lithology, mineralogy, mineralisation, veins, structures, weathering, colour and other noticeable features. This is generally qualitative except for % of sulphides and vein mineral content. Core trays are photographed in wet form. All drill holes are geologically logged in full. Core was cut using a conventional automatic core saw with core holding support. All samples are collected from the same side of drill core. If core, whether cut or sawn and whether quarter, half or all core taken. If non‐core, whether riffled, tube sampled, rotary split, etc and whether sampled wet or dry. Sub‐sampling techniques and sample preparation For all sample types, the nature, quality and appropriateness of the sample preparation technique. Quality control procedures adopted for all subsampling stages to maximise representivity of samples. Measures taken to ensure that the sampling is representative of the in situ material collected, A half-core sample is submitted for assay analysis. Where core was incompetent due to being transported cover, weathered rock, or soft rock due to faulting, representative samples were collected along the axis of the core. This information is recorded in the cut-sheet and loaded into database. Not applicable as results are for core drilling. Drill core is cut in half along the length and the total half core submitted as the sample. This procedure meets industry standards where approximately 50% of the total sample taken from the diamond core is submitted. All mineralised intervals and surrounding wall rock were submitted for assay. Sample weights are recorded by the lab. Samples were delivered by Legacy Minerals Holdings personnel to ALS Minerals Laboratory, Orange NSW. Sample preparation will comprise of an industry standard of drying, jaw crushing and pulverising to -75 microns (85% passing) (ALS code PUL-23). Pulverisers are washed with QAQC tests undertaken (PUL-QC). Samples are dried, crushed and pulverized to produce a homogenous representative sub‐sample for analysis. Quality control procedures include submission of Certified Reference Materials (standards) and duplicates with each sample batch. QAQC results are routinely reviewed to identify and resolve any issues. No sub-sampling is completed by LGM. All subsampling of the prepared core is completed by the laboratory. The remaining half-core is stored and allows assay values to be viewed against the geology; and, where required, further samples may be SIGN UP TO LEGACY MINERALS’ INTERACTIVE INVESTOR HUB ASX: LGM Page 13 of 18 including for instance results for field duplicate/second‐half sampling. Whether sample sizes are appropriate to the grain size of the material being sampled. The nature, quality and appropriateness of the assaying and laboratory procedures used and whether the technique is considered partial or total. Quality of assay data and laboratory tests For geophysical tools, spectrometres, handheld XRF instruments, etc, the parametres used in determining the analysis including instrument make and model, reading times, calibrations factors applied and their derivation, etc. Nature of quality control procedures adopted (e.g. standards, blanks, duplicates, external laboratory checks) and whether acceptable levels of accuracy (i.e. lack of bias) and precision have been established. submitted for quality assurance. Quarter core resampling may be completed in zones where appropriate. The sample sizes are appropriate to correctly represent the mineralization based on style of mineralisation. All samples were analysed by ALS Global. Samples are crushed to 6mm and then pulverized to 85% passing 75 microns. Gold is determined using a 50g charge. The resultant prill is dissolved in aqua regia with gold determined by flame AAS. The lower detection limit for gold is 0.002 ppm, which is believed to be an appropriate detection level. All other elements (total 48 element suite) are analysed using a 4-acid acid digest and an ICP finish (ALS code: ME-MS61 + Au-AA21 + Hg-MS42) and undergo spectral analysis (TRSPEC-20). No geophysical tools or other handheld XRF instruments were used to determine grade. Laboratory QAQC involves the use of internal lab standards using certified reference material (CRMs), blanks and pulp duplicates as part of in‐ house procedures. The Company also submits a suite of CRMs and blanks where appropriate and selects appropriate samples for duplicates. CRM’s are inserted approximately every 50 samples. Sample preparation checks for fineness are performed by the laboratory to ensure the grind size of 85% passing 75μm is being attained. Verification of sampling and assaying The verification of significant intersections by either independent or alternative company personnel. Significant intersections are verified by the Company’s technical staff. The use of twinned holes. No twinned holes were completed in the current drill programme. Documentation of primary data, data entry procedures, data verification, data storage (physical and electronic) protocols. Discuss any adjustment to assay data. Accuracy and quality of surveys used to locate drill holes (collar and down‐hole surveys), trenches, Primary data is captured onto a laptop through excel and using Datashed software and includes geological logging, sample data and QA/QC information. This data, together with the assay data, is stored both locally and entered into the LGM central online database which is managed by external consultants. All primary assay data is received from the laboratory as electronic data files which are imported into sampling database with verification procedures in place. QAQC analysis is undertaken for each laboratory report No adjustments or calibrations will be made to any primary assay data collected for the purpose of reporting assay grades and mineralised intervals. A handheld Garmin GPSmap 65 was used to pick up collars with an averaged accuracy of 1m. SIGN UP TO LEGACY MINERALS’ INTERACTIVE INVESTOR HUB ASX: LGM Page 14 of 18 Location of data points mine workings and other locations used in Mineral Resource estimation. Downhole surveys are conducted using a downhole Gyro during drilling to record and monitor deviations of th